I.S. EN 16678:2015
Current
The latest, up-to-date edition.
SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUT-OFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA
Hardcopy , PDF
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Units of measurement and test conditions
6 Construction requirements
7 Performance
8 EMC/Electrical requirements
9 Marking, installation and operating instructions
Annex A (informative) - Gas connections in common
use in the various countries
Annex B (informative) - Leak-tightness test volumetric
method
Annex C (informative) - Leak-tightness test pressure
loss method
Annex D (normative) - Conversion of pressure loss into
leakage rate
Annex E (normative) - Electrical/electronic component
fault modes
Annex F (normative) - Additional requirements for safety
accessories and pressure accessories as defined in
EU Directive 97/23/EC
Annex G (informative) - Materials for pressurized parts
Annex H (informative) - Additional materials for pressurized
parts
Annex I (normative) - Requirements for controls used in DC
supplied gas burners and gas burning appliances
Annex J (normative) - Method for the determination of a
Safety Integrity Level (SIL)
Annex K (normative) - Method for the determination of a
Performance Level (PL)
Annex L (informative) - Relationship between Safety Integrity
Level (SIL) and Performance Level (PL)
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2009/142/EC
relating to appliances burning gaseous fuels
Annex ZB (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 97/23/EC
relating to pressure equipment
Bibliography
Provides the safety, design, construction and performance requirements and testing for automatic shut-off valves with or without modulating control functions (hereafter referred to as valves) for burners and appliances burning one or more gaseous fuels according to EN 437:2003+A1:2009.
| DocumentType |
Standard
|
| Pages |
48
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| SupersededBy |
| Standards | Relationship |
| EN 16678:2015 | Identical |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 175301-803:2006 | Detail Specification: Rectangular connectors - Flat contacts, 0,8 mm thickness, locking screw not detachable |
| EN 14917:2009+A1:2012 | Metal bellows expansion joints for pressure applications |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN 1759-4:2003 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 4: Aluminium alloy flanges |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN 12516-1:2014 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
| EN 12266-1:2012 | Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements |
| ISO 8573-1:2010 | Compressed air Part 1: Contaminants and purity classes |
| EN 13906-2:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
| EN 1092-4:2002 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 61058-1:2016 | Switches for appliances - Part 1: General requirements |
| EN 50156-1:2015 | Electrical equipment for furnaces and ancillary equipment - Part 1: Requirements for application design and installation |
| EN 61058-1:2002/A2:2008 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| EN 298:2012 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
| EN 12760:2016 | Industrial valves - Socket welding ends for steel valves |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| EN 12516-2:2014 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.