I.S. EN 55011:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INDUSTRIAL, SCIENTIFIC AND MEDICAL EQUIPMENT - RADIO-FREQUENCY DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT
Hardcopy , PDF
28-03-2020
English
01-01-2016
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National Foreword
European foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 National measures and frequencies designated
for ISM use
5 Classification of equipment
7 Measurement requirements
8 Special provisions for test site measurements
(9 kHz to 1 GHz)
9 Radiation measurements: 1 GHz to 18 GHz
10 Measurement in situ
11 Safety precautions for emission measurements
on ISM RF equipment
12 Measurement uncertainty
Annex A (informative) - Examples of equipment classification
Annex B (informative) - Precautions to be taken in the use of
a spectrum analyzer
Annex C (normative) - Measurement of electromagnetic
radiation disturbance in the presence of signals from
radio transmitters
Annex D (informative) - Propagation
of interference from industrial radio-frequency
equipment at frequencies between 30 MHz and
300 MHz
Annex E (informative) - Recommendations of CISPR
for protection of certain radio services in particular
areas
Annex F (informative) - Frequency bands allocated for
safety-related radio services
Annex G (informative) - Frequency bands allocated for
sensitive radio services
Annex H (informative) - Statistical assessment of series
produced equipment against the requirements of
CISPR standards
Annex I (normative) - Artificial Network (AN) for the
assessment of disturbance voltages at d.c. power
ports of semiconductor power converters
Annex J (informative) - Measurements on Grid Connected
Power Converters (GCPC) - Setups for an effective test
site configuration
Annex K (informative) - Test site configuration and
instrumentation - Guidance on prevention of saturation
effects in mitigation filters of transformer-less power
converters during type tests according to this standard
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Annex ZB (normative) - Frequencies designated on
a national basis in CENELEC countries for use
as fundamental ISM frequencies
Annex ZZ (informative) - Coverage of Essential
Requirements of EU Directives
This International Standard applies to industrial, scientific and medical electrical equipment operating in the frequency range 0 Hz to 400 GHz and to domestic and similar appliances designed to generate and/or use locally radio-frequency energy.
Committee |
CLC/TC 210
|
DocumentType |
Standard
|
ISBN |
978-2-8322-2707-7
|
Pages |
212
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
UNE-EN 55011:2011 | Identical |
NF EN 55011 : 2016 AMD 1 2017 | Identical |
EN 55011:2016 | Identical |
NEN EN 55011 : 2016 AMD 1 2017 | Identical |
BS EN 55011 : 2016 | Identical |
SN EN 55011 : 2016 AMD 1 2017 | Identical |
DIN EN 55011 : 2011 | Identical |
NBN EN 55011 : 2016 | Identical |
EN 55011:2016/A1:2017 | Identical |
CISPR 14-1:2016 | Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission |
EN 62135-2:2015 | Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements |
CISPR 16-4-2:2011+AMD1:2014 CSV | Specification for radio disturbance and immunity measuring apparatusand methods - Part 4-2: Uncertainties, statistics and limit modelling - Measurement instrumentation uncertainty |
EN 55016-2-3:2017 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements |
EN 55016-1-4:2010/A2:2017 | SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-4: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - ANTENNAS AND TEST SITES FOR RADIATED DISTURBANCE MEASUREMENTS (CISPR 16-1-4:2010/A2:2017) |
CISPR 16-1-4:2010+AMD1:2012+AMD2:2017 CSV | Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements |
CISPR 16-1-1:2015 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus |
IEC TR 60083:2015 | Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC |
IEC 60364-5-51:2005 | Electrical installations of buildings - Part 5-51: Selection and erection of electrical equipment - Common rules |
CISPR 16-2-1:2014 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements |
CISPR 15:2013+AMD1:2015 CSV | Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment |
IEC 60974-10:2014+AMD1:2015 CSV | Arc welding equipment - Part 10: Electromagnetic compatibility (EMC)requirements |
CISPR TR 16-4-3:2004+AMD1:2006 CSV | Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-3: Uncertainties, statistics and limit modelling - Statistical considerations in the determination of EMC compliance of mass-produced products |
IEC TR 61000-2-5:2017 | Electromagnetic compatibility (EMC) - Part 2-5: Environment - Description and classification of electromagnetic environments |
IEC 60364-1:2005 | Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
IEC 60601-1-2:2014 | Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests |
EN 60601-1-2:2015 | Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests |
IEC 60601-2-2:2017 | Medical electrical equipment - Part 2-2: Particular requirements for the basic safety and essential performance of high frequency surgical equipment and high frequency surgical accessories |
EN 61307:2011 | Industrial microwave heating installations - Test methods for the determination of power output |
CISPR TR 16-2-5:2008 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-5: In situ measurements for disturbing emissions produced by physically large equipment |
IEC 62135-2:2015 | Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements |
CISPR 16-2-3:2016 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements |
CISPR TR 16-4-4:2007 | Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-4: Uncertainties, statistics and limit modelling - Statistics of complaints and a model for the calculation of limits for the protection of radio services |
EN 60974-10:2014/A1:2015 | ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS (IEC 60974-10:2014/A1:2015) |
IEC 61307:2011 | Industrial microwave heating installations - Test methods for the determination of power output |
EN 55016-2-1:2014/A1:2017 | SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 2-1: METHODS OF MEASUREMENT OF DISTURBANCES AND IMMUNITY - CONDUCTED DISTURBANCE MEASUREMENTS (CISPR 16-2-1:2014/A1:2017) |
IEC 60705:2010+AMD1:2014 CSV | Household microwave ovens - Methods for measuring performance |
EN 55016-1-1:2010/A2:2014 | SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS (CISPR 16-1-1:2010/A2:2014) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.