I.S. EN 60034-18-41:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ROTATING ELECTRICAL MACHINES - PART 18-41: PARTIAL DISCHARGE FREE ELECTRICAL INSULATION SYSTEMS (TYPE 1) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION AND QUALITY CONTROL TESTS
Hardcopy , PDF
12-10-2019
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Machine terminal voltages arising
from converter operation
5 Electrical stresses in the insulation system
of machine windings
6 Types of machine insulation
7 Stress categories for Type I insulation systems
used in converter fed machines
8 Design qualification and type tests for Type I
insulation systems
9 Test equipment
10 Qualification of the design of Type
I insulation systems
11 Type test procedure for Type I
insulation systems
12 Routine tests
13 Analysis, reporting and classification
Annex A (informative) - Derivation of
possible terminal voltages in
service for a converter-fed
machine
Annex B (normative) - Derivation of test
voltages for Type I insulation systems
Annex C (normative) - Derivation of
allowable voltages in service
Bibliography
Annex ZA (normative) - Normative
references to international
publications with their
corresponding European
publications
Specifies criteria for assessing the insulation system of stator/rotor windings which are subjected to voltage-source pulse width-modulation (PMW) drives.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
96
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 60034-18-41:2014 | Identical |
| EN 60034-18-1:2010 | Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines |
| CLC/TS 60034-27:2011 | Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines |
| EN 60034-18-21:2013 | Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification |
| EN 60034-18-31 : 2012 | ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012) |
| IEC TS 60034-27:2006 | Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines |
| IEC TS 61934:2011 | Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses |
| IEC TS 60034-18-42:2008 | Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters |
| IEC TS 61800-8:2010 | Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface |
| IEC 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
| IEC 60034-18-1:2010 | Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines |
| IEC TS 60034-25:2014 | Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide |
| EN 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 60034-18-21:2012 | Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification |
| CLC/TS 60034-25:2008 | Rotating electrical machines - Part 25: Guidance for the design and performance of a.c. motors specifically designed for converter supply |
| CLC/TS 60034-18-42:2011 | Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters |
| IEC 60034-18-31:2012 | Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.