I.S. EN 60335-2-75:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-75: PARTICULAR REQUIREMENTS FOR COMMERCIAL DISPENSING APPLIANCES AND VENDING MACHINES
Hardcopy , PDF
07-05-2023
English
01-01-2004
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
Introduction
1 Scope
2 Normative references
3 Definitions
4 General requirement
5 General conditions for the tests
6 Classification
7 Marking and instructions
8 Protection against access to live parts
9 Starting of motor-operated appliances
10 Power input and current
11 Heating
13 Leakage current and electric strength at operating temperature
14 Transient over-voltages
15 Moisture resistance
16 Leakage current and electric strength
17 Overload protection of transformers and associated circuits
18 Endurance
19 Abnormal operation
20 Stability and mechanical hazards
21 Mechanical strength
22 Construction
23 Internal wiring
24 Components
25 Supply connection and external flexible cords
26 Terminals for external conductors
27 Provision for earthing
28 Screws and connections
29 Clearances, creepage distances and solid insulation
30 Resistance to heat and fire
31 Resistance to rusting
32 Radiation, toxicity and similar hazards
Annexes
Annex AA (normative) Aging test for elastomeric parts
Annex ZC (normative) Normative references to international
publications with their
corresponding European publications
Annex ZAA (normative) Commercial electric espresso-coffee
machines that can also be heated by gas
Annex ZBB (normative) Measurement of acoustical noise
Bibliography
Deals with the safety of commercial electric dispensing appliances and vending machines for preparation or delivery of food, drinks and consumer products, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances.
| DevelopmentNote |
Supersedes I.S. EN 60335-2-63. (09/2004) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
67
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 60335-2-75 : 2004 | Identical |
| EN 60335-2-75:2004/A12:2010 | Identical |
| IEC 60335-2-75:2012+AMD1:2015 CSV | Identical |
| NF EN 60335-2-75 : 2005 AMD 12 2013 | Identical |
| DIN EN 60335-2-75 : 2010 | Identical |
| UNE-EN 60335-2-75:2005 | Identical |
| SN EN 60335-2-75 : 2004 AMD 12 2010 | Identical |
| IEC 60335-2-82:2017 | Household and similar electrical appliances - Safety - Part 2-82: Particular requirements for amusement machines and personal service machines |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| IEC 60335-2-24:2010+AMD1:2012+AMD2:2017 CSV | Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| IEC 60335-2-64:2002+AMD1:2007+AMD2:2017 CSV | Household and similar electrical appliances - Safety - Part 2-64: Particular requirements for commercial electric kitchen machines |
| IEC 60335-2-25:2010+AMD1:2014+AMD2:2015 CSV | Household and similar electrical appliances - Safety - Part 2-25: Particular requirements for microwave ovens, including combinationmicrowave ovens |
| IEC 60335-2-47:2002+AMD1:2008+AMD2:2017 CSV | Household and similar electrical appliances - Safety - Part 2-47: Particular requirements for commercial electric boiling pans |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| IEC 60335-2-34:2012+AMD1:2015+AMD2:2016 CSV | Household and similar electrical appliances - Safety - Part 2-34:Particular requirements for motor-compressors |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 60335-2-34:2013 | Household and similar electrical appliances - Safety - Part 2-34: Particular requirements for motor-compressors |
| CR 1472:1997 | General guidance for the marking of gas appliances |
| CR 1749 : 2001 | EUROPEAN SCHEME FOR THE CLASSIFICATION OF GAS APPLIANCES ACCORDING TO THE METHOD OF EVACUATION OF THE PRODUCTS OF COMBUSTION (TYPES) |
| EN ISO 3743-1:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010) |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| IEC 60335-2-50:2002+AMD1:2007+AMD2:2017 CSV | Household and similar electrical appliances - Safety - Part 2-50: Particular requirements for commercial electric bains-marie |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.