I.S. EN 61347-2-10:2001
Current
The latest, up-to-date edition.
LAMP CONTROLGEAR - PART 2-10: PARTICULAR REQUIREMENTS FOR ELECTRONIC INVERTORS AND CONVERTORS FOR HIGH-FREQUENCY OPERATION OF COLD START TUBULAR DISCHARGE LAMPS (NEON TUBES) (IEC 61347-2-10:2000 (EQV))
Hardcopy , PDF
English
01-01-2001
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Terminals
9 Provisions for earthing
10 Protection against accidental contact with live parts
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings
14 Normal conditions
15 Abnormal conditions
16 Fault conditions
17 Construction
18 Creepage distances and clearances
19 Protective circuits
20 Screws, current-carrying parts and connections
21 Resistance to heat, fire and tracking
22 Resistance to corrosion
23 No-load rated output voltage and rated output current
Annex A (normative) - Test to establish whether
a conductive part is a live part which may cause
an electric shock
Annex B (normative) - Particular requirements for
thermally protected lamp controlgear
Annex C (normative) - Particular requirements for
electronic lamp controlgear with means of protection
against overheating
Annex D (normative) - Requirements for carrying
out the heating tests of thermally protected
lamp controlgear
Annex E (normative) - Use of constant S other than
4500 in t[w] tests
Annex F (normative) - Draught-proof enclosure
Annex G (normative) - Explanation of the derivation
of the values of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Measurement of currents and
voltages in the output circuits of electronic invertors
or convertors for neon tubes
Annex ZA (normative) - Normative references to
international publications with their corresponding
European publications
Describes particular requirements for electronic invertors and convertors for high-frequency operation of tubular cold-cathode discharge lamps used in signs and luminous discharge tube installations and operating with an output voltage exceeding 1000 V but not exceeding 10000 V for direct connection to supply voltages not exceeding 1000 V at 50 Hz or 60 Hz or 1000 V d.c.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| SN EN 61347-2-10 : 2001 | Identical |
| EN 61347-2-10:2001/corrigendum:2010 | Identical |
| NF EN 61347-2-10 : 2001 AMD 1 2009 | Identical |
| UNE-EN 61347-2-10:2004 | Identical |
| DIN EN 61347-2-10 : 2009 COR 1 2011 | Identical |
| BS EN 61347-2-10 : 2001 | Identical |
| IEC 61347-1:2015 RLV | Lamp controlgear - Part 1: General and safety requirements |
| EN 61347-1:2015 | Lamp controlgear - Part 1: General and safety requirements |
| ISO 3864:1984 | Safety colours and safety signs |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.