I.S. EN 61347-2-5:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LAMP CONTROLGEAR - PART 2-5: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR PUBLIC TRANSPORT LIGHTING (IEC 61347-2-5:2000 (EQV))
Hardcopy , PDF
15-11-2011
English
01-01-2001
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Protection against accidental contact with live
parts
9 Terminals
10 Provisions for earthing
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings
14 Pulse voltages
15 Abnormal conditions
16 Fault conditions
17 Construction
18 Creepage distances and clearances
19 Screws, current-carrying parts and connections
20 Resistance to heat, fire and tracking
21 Resistance to corrosion
Annex A (normative) - Test to establish whether
a conductive part is a live part which
may cause an electric shock
Annex B (normative) - Particular requirements for thermally
protected lamp controlgear
Annex C (normative) - Particular requirements for electronic
lamp controlgear with means of protection against
overheating
Annex D (normative) - Requirements for carrying out the heating
tests of thermally protected lamp controlgear
Annex E (normative) - Use of constant S other than 4500 in
t[w] tests
Annex F (normative) - Draught-proof enclosure
Annex G (normative) - Explanation of the derivation of the
values of pulse voltages
Annex H (normative) - Tests
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Describes particular safety requirements for d.c. supplied electronic ballasts intended for operation from power sources likely to have attendant transients and surges, for example, for road and railway vehicles, tramcars, and craft used for public transport.
DevelopmentNote |
Together with I.S. EN 61347-1 and parts 2-1, 2-2, 2-3, 2-4, 2-6, 2-7, 2-8 and 2-9 of I.S. EN 61347 supersedes I.S. EN 60920, I.S. EN 60922, I.S. EN 60924, I.S. EN 60926, I.S. EN 60928 and I.S. EN 61046. (07/2005)
|
DocumentType |
Standard
|
Pages |
37
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
EN 61347-2-5:2001/corrigendum:2010 | Identical |
BS EN 61347-2-5:2001 | Identical |
NF EN 61347-2-5 : 2001 | Identical |
SN EN 61347-2-5 : 2001 | Identical |
UNE-EN 61347-2-5:2002 | Identical |
IEC 61347-2-5:2000 | Identical |
IEC 61347-1:2015 RLV | Lamp controlgear - Part 1: General and safety requirements |
IEC 60925:1989+AMD1:1996+AMD2:2001 CSV | DC supplied electronic ballasts for tubular fluorescent lamps - Performance requirements |
EN 61347-1:2015 | Lamp controlgear - Part 1: General and safety requirements |
EN 60925:1991/A2:2001 | SPECIFICATION FOR PERFORMANCE REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.