I.S. EN 88-1:2011
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA
Hardcopy , PDF
28-02-2016
English
18-04-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Units of measurement and test conditions
6 Construction requirements
7 Performance
8 EMC/Electrical requirements
9 Marking, installation and operating instructions
Annex A (informative) - Gas connections in common
use in the various countries
Annex B (informative) - Leak-tightness test - volumetric
method
Annex C (informative) - Leak-tightness test - pressure loss
method
Annex D (normative) - Conversion of pressure loss into
leakage rate
Annex E (normative) - Electrical/electronic component fault
modes
Annex F (normative) - Additional requirements for safety
accessories and pressure accessories as defined in
EC Directive 97/23/EC
Annex G (normative) - Materials for pressurized parts
Annex H (informative) - - Additional materials for pressurized
parts
Annex I (normative) - Requirements for controls used in DC
supplied gas burners and gas burning appliances
Annex AA (informative) - Typical pressure regulators and
pressure regulator parts
Annex BB (informative) - Overview of requirements and test
conditions, and examples of performance curves for
pressure regulators
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EC Directive 2009/142/EC relating to appliances
burning gaseous fuels
Bibliography
Describes the safety, construction and performance requirements for pressure regulators and pneumatic gas/air ratio pressure regulators (zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure regulator), intended for use with gas burners, gas appliances and similar use, hereafter referred to as 'pressure regulators'.
| DevelopmentNote |
Supersedes I.S. EN 88. (01/2008) Supersedes I.S. EN 12067-1 & I.S. EN 12078. (05/2011) 2011 Edition Re-Issued in February 2016 & incorporates AMD 1 2016. (03/2016)
|
| DocumentType |
Standard
|
| Pages |
56
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Supersedes |
| Standards | Relationship |
| ONORM EN 88-1 : 2016 | Identical |
| UNI EN 88-1 : 2011 | Identical |
| NEN EN 88-1 : 2011 + A1 2016 | Identical |
| NBN EN 88-1 : 2011 + A1 2016 | Identical |
| BS EN 88-1 : 2011 | Identical |
| SN EN 88-1+A1:2016 | Identical |
| NS EN 88-1 : 2011 + A1 2016 | Identical |
| DIN EN 88-1:2016-06 | Identical |
| NF EN 88-1 : 2011 + A1 2016 | Identical |
| EN 88-1:2011+A1:2016 | Identical |
| EN 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 175301-803:2006 | Detail Specification: Rectangular connectors - Flat contacts, 0,8 mm thickness, locking screw not detachable |
| EN 88-2:2007 | Pressure regulators and associated safety devices for gas appliances - Part 2: Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar |
| EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
| EN 1854:2010 | Pressure sensing devices for gas burners and gas burning appliances |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 13786:2004+A1:2008 | Automatic change-over valves having a maximum outlet pressure of up to and including 4 bar with a capacity of up to and including 100 kg/h, and their associated safety devices for butane, propane or their mixtures |
| EN 13785:2005+A1:2008 | Regulators with a capacity of up to and including 100 kg/h, having a maximum nominal outlet pressure of up to and including 4 bar, other than those covered by EN 12864 and their associated safety devices for butane, propane or their mixtures |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| IEC 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.