I.S. EN ISO 19432:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BUILDING CONSTRUCTION MACHINERY AND EQUIPMENT - PORTABLE, HAND-HELD, INTERNAL COMBUSTION ENGINE DRIVEN CUT-OFF MACHINES - SAFETY REQUIREMENTS (ISO 19432:2012)
Hardcopy , PDF
English
24-07-2012
20-05-2021
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Safety requirements and verification
5 Information for use
Annex A (normative) - Strength test of cut-off wheel guard
Annex B (normative) - Noise test code - Engineering method
(grade 2 of accuracy)
Annex C (normative) - Measurement of vibration values at the
handles
Annex D (normative) - Cut-off machine positions
Annex E (informative) - Summary of results from round-robin
tests (2007 and 2008) on one cut-off machine
Annex F (informative) - List of significant hazards
Bibliography
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of
EU Directive 2006/42/EC
Describes safety requirements, and measures for their verification, for the design and construction of portable, hand-held, internal combustion engine-driven, cut-off machines, intended to be used by a single operator in the cutting of construction materials, such as asphalt, concrete, stone and metal.
| DevelopmentNote |
Supersedes I.S. EN 1454. (05/2006)
|
| DocumentType |
Standard
|
| Pages |
57
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN ISO 19432 : 2012 | Identical |
| NBN EN ISO 19432 : 2012 | Identical |
| NS EN ISO 19432 : 2012 | Identical |
| EN ISO 19432:2012 | Identical |
| NF EN ISO 19432 : 2012 | Identical |
| DIN EN ISO 19432:2012-12 | Identical |
| BS EN ISO 19432:2012 | Identical |
| ISO 19432:2012 | Identical |
| UNE-EN ISO 19432:2013 | Identical |
| EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 5349-2:2001 | Mechanical vibration — Measurement and evaluation of human exposure to hand-transmitted vibration — Part 2: Practical guidance for measurement at the workplace |
| ISO 3744:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for an essentially free field over a reflecting plane |
| ISO 20643:2005 | Mechanical vibration — Hand-held and hand-guided machinery — Principles for evaluation of vibration emission |
| ISO/TR 11688-1:1995 | Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 1: Planning |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| ISO 7293:1997 | Forestry machinery — Portable chain saws — Engine performance and fuel consumption |
| ISO 7914:2002 | Forestry machinery — Portable chain-saws — Minimum handle clearance and sizes |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| CR 1030-1:1995 | Hand-arm vibration - Guidelines for vibration hazards reduction - Part 1: Engineering methods by design of machinery |
| ISO 13942:2000 | Bonded abrasive products — Limit deviations and run-out tolerances |
| ISO 11820:1996 | Acoustics — Measurements on silencers in situ |
| ISO 14982:1998 | Agricultural and forestry machinery — Electromagnetic compatibility — Test methods and acceptance criteria |
| ISO 6531:2017 | Machinery for forestry — Portable chain-saws — Vocabulary |
| ISO 16063-1:1998 | Methods for the calibration of vibration and shock transducers — Part 1: Basic concepts |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 8041:2005 | Human response to vibration — Measuring instrumentation |
| ISO 13857:2008 | Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 3767-5:2016 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 5: Symbols for manual portable forestry machines |
| IEC 60745-1:2006 | Hand-held motor-operated electric tools - Safety - Part 1: General requirements |
| ISO 14163:1998 | Acoustics — Guidelines for noise control by silencers |
| ISO 22868:2011 | Forestry and gardening machinery — Noise test code for portable hand-held machines with internal combustion engine — Engineering method (Grade 2 accuracy) |
| ISO 5349-1:2001 | Mechanical vibration — Measurement and evaluation of human exposure to hand-transmitted vibration — Part 1: General requirements |
| ISO 22917:2016 | Precision superabrasives — Limit deviations and run-out tolerances for grinding wheels with diamond or cubic boron nitride |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 2: Introduction to the physics of low-noise design |
| ISO 11201:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO 11691:1995 | Acoustics — Measurement of insertion loss of ducted silencers without flow — Laboratory survey method |
| ISO 11684:1995 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Safety signs and hazard pictorials — General principles |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.