I.S. EN ISO 2692:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL TOLERANCING - MAXIMUM MATERIAL REQUIREMENT (MMR), LEAST MATERIAL REQUIREMENT (LMR) AND RECIPROCITY REQUIREMENT (RPR) (ISO 2692:2014)
Hardcopy , PDF
English
01-01-2014
22-07-2021
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Maximum material requirement, MMR and least
material requirement, LMR
5 Reciprocity requirement, RPR
Annex A (informative) - Examples of tolerancing
with [M],[L] and [R]
Annex B (informative) - Concept diagram
Annex C (informative) - Relation to the GPS matrix
model
Bibliography
Describes the maximum material requirement, the least material requirement and the reciprocity requirement.
| DocumentType |
Standard
|
| Pages |
62
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN ISO 2692 : 2015 | Identical |
| EN ISO 2692:2014 | Identical |
| NS EN ISO 2692 : 2014 | Identical |
| ISO 2692:2014 | Identical |
| DIN EN ISO 2692:2015-12 | Identical |
| NBN EN ISO 2692 : 2015 | Identical |
| NF EN ISO 2692 : 2015 | Identical |
| BS EN ISO 2692:2014 | Identical |
| ONORM EN ISO 2692 : 2015 | Identical |
| UNE-EN ISO 2692:2015 | Identical |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) — Masterplan |
| ISO 8015:2011 | Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 7083:1983 | TECHNICAL DRAWINGS - SYMBOLS FOR GEOMETRICAL TOLERANCING - PROPORTIONS AND DIMENSIONS |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO 17450-1:2011 | Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification |
| ISO 286-1:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits |
| ISO 14660-2:1999 | Geometrical Product Specifications (GPS) — Geometrical features — Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature |
| ISO 22432:2011 | Geometrical product specifications (GPS) — Features utilized in specification and verification |
| ISO 14405-1:2016 | Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes |
| ISO 5458:1998 | Geometrical Product Specifications (GPS) — Geometrical tolerancing — Positional tolerancing |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.