I.S. EN ISO 3167:2014
Current
The latest, up-to-date edition.
PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014)
Hardcopy , PDF
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
1 Scope
2 Normative references
3 Dimensions of test specimens
4 Preparation of test specimen
5 Report on preparation of test specimens
Annex A (informative) - Recommended applications
for multipurpose test specimens or parts thereof
Annex B (informative) - Consequences of changes
in geometry
Bibliography
Describes requirements relating to multipurpose test specimens for plastic moulding materials intended for processing by injection or direct compression moulding.
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN ISO 3167 : 2014 | Identical |
| NEN EN ISO 3167 : 2014 | Identical |
| EN ISO 3167:2014 | Identical |
| BS EN ISO 3167:2014 | Identical |
| NBN EN ISO 3167 : 2014 | Identical |
| DIN EN ISO 3167:2014-11 | Identical |
| ISO 3167:2014 | Identical |
| NS EN ISO 3167 : 2014 | Identical |
| UNE-EN ISO 3167:2014 | Identical |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 4589-3:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 22088-2:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 2: Constant tensile load method |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 2039-1:2001 | Plastics — Determination of hardness — Part 1: Ball indentation method |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 180:2000 | Plastics — Determination of Izod impact strength |
| ISO 22088-3:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 3: Bent strip method |
| ISO 899-2:2003 | Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading |
| ISO 1183-3:1999 | Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometer method |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| IEC 60426:2007 | Electrical insulating materials - Determination of electrolytic corrosion caused by insulating materials - Test methods |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 22088-4:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 4: Ball or pin impression method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 178:2010 | Plastics — Determination of flexural properties |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.