ISO 17484-1:2014
Current
Current
The latest, up-to-date edition.
Plastics piping systems — Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) — Part 1: Specifications for systems
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
English
Published date
23-05-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.
ISO 17484-1:2014 specifies the general requirements and the performance requirements for multilayer pipe systems based on pipes, fittings and their joints intended to be used for gas supply within buildings.
PE-X and PE pipes composed of one stress-designed layer, adhesive and a barrier layer are also covered by ISO 17484-1:2014.
ISO 17484-1:2014 gives guidance for the design of piping systems consisting of multilayer pipes based on thermoplastics, for which at least 60 % of the wall thickness is polymeric material. Polymeric materials intended for stress-designed layers and all inner layers are required to be polyethylene (PE) and/or crosslinked polyethylene (PE-X) in accordance with Annex A of ISO 17484-1:2014.
ISO 17484-1:2014 applies to systems that operate at temperatures of −20 °C up to +60 °C.
For the purpose of ISO 17484-1:2014, crosslinked polyethylene (PE-X) and adhesive layers are considered as thermoplastic materials.
For sizes greater than 63 mm the requirements of ISO 18225 have to be fulfilled in addition.
ISO 17484-1:2014 is applicable for piping systems used in buildings to supply gas with a maximum operating pressure up to and including 500 kPa (5 bar).
ISO 17484-1:2014 applies to the following fuels:
- Category D gaseous fuel: natural gas;
- Category E gaseous fuel: LPG vapour, and natural gas or LPG vapour.
| Committee |
ISO/TC 138/SC 4
|
| DevelopmentNote |
Supersedes ISO/DIS 17484-1. (05/2014)
|
| DocumentType |
Standard
|
| Pages |
33
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| SS-ISO 17484-1:2019 | Identical |
| BS ISO 17484-1:2014 | Identical |
| NEN ISO 17484-1 : 2014 | Identical |
| DIN EN 1254-8:2012-12 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| 12/30256669 DC : 0 | BS ISO 4437-2 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| 04/30126883 DC : DRAFT DEC 2004 | ISO 4437 - BURIED POLYETHYLENE (PE) PIPES FOR THE SUPPLY OF GASEOUS FUELS - METRIC SERIES - SPECIFICATIONS |
| EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| UNE-EN 1555-2:2011 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| BS EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Pipes |
| I.S. 813:2014+A1:2017 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| BS ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Pipes |
| BS EN 1254-8:2012 | Copper and copper alloys. Plumbing fittings Fittings with press ends for use with plastics and multilayer pipes |
| ISO 4437:2007 | Buried polyethylene (PE) pipes for the supply of gaseous fuels Metric series Specifications |
| ISO 17484-2:2009 | Plastics piping systems — Multilayer pipe systems for indoor gas installations — Part 2: Code of pratice |
| DIN EN 1555-2:2010-12 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| I.S. EN 1555-2:2010 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| 08/30153234 DC : DRAFT JAN 2008 | BS ISO 17484-2 - PLASTICS PIPING SYSTEMS - MULTILAYER PIPE SYSTEMS FOR INDOOR GAS INSTALLATIONS - PART 2: CODE OF PRACTICE |
| 11/30213590 DC : 0 | BS EN 1254-8 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| UNI EN 1254-8 : 2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| BS ISO 4437:2007 | Buried polyethylene (PE) pipes for the supply of gaseous fuels. Metric series. Specifications |
| I.S. 813:2014 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| UNI EN 1555-2 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| UNE-EN 1254-8:2013 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| EN 1254-8:2012 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| UNI/TS 11344 : 2009 | METALLO-PLASTIC MULTILAYER PIPING SYSTEMS AND FITTINGS FOR INDOOR INSTALLATION FOR THE CONVEYANCE OF GASEOUS FUELS |
| I.S. EN 1254-8:2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 2: Pipes |
| 08/30191147 DC : 0 | BS EN 1555-2 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| UNE 53008-1:2014 | Plastics piping systems. Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa). Part 1: Specifications for pipes, fittings and the system |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| ISO 4437-5:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 5: Fitness for purpose of the system |
| EN 1775:2007 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| ISO 10146:1997 | Crosslinked polyethylene (PE-X) pipes Effect of time and temperature on the expected strength |
| ISO 6447:1983 | Rubber seals Joint rings used for gas supply pipes and fittings Specification for material |
| ISO 14531-1:2002 | Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 1: Pipes |
| ISO 161-1:1996 | Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series |
| DVGW W 542 : 2009 | COMPOUND PIPES IN THE DRINKING WATER INSTALLATION; REQUIREMENTS AND TESTING |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 17456:2006 | Plastics piping systems Multilayer pipes Determination of long-term strength |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 2: Pipes |
| ISO/TS 10839:2000 | Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 4437-1:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 1: General |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 713:1993 | Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| ISO 24033:2009 | Polyethylene of raised temperature resistance (PE-RT) pipes — Effect of time and temperature on the expected strength |
| ISO 14531-3:2010 | Plastics pipes and fittings Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels Metric series Specifications Part 3: Fittings for mechanical jointing (including PE-X/metal transitions) |
| ISO/TR 10837:1991 | Determination of the thermal stability of polyethylene (PE) for use in gas pipes and fittings |
| ISO 10508:2006 | Plastics piping systems for hot and cold water installations — Guidance for classification and design |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 14531-2:2004 | Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 2: Fittings for heat-fusion jointing |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 13480:1997 | Polyethylene pipes Resistance to slow crack growth Cone test method |
| ISO 18225:2012 | Plastics piping systems — Multilayer piping systems for outdoor gas installations — Specifications for systems |
| ISO 4437-3:2014 | Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 3: Fittings |
| ISO 10147:2011 | Pipes and fittings made of crosslinked polyethylene (PE-X) Estimation of the degree of crosslinking by determination of the gel content |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ISO 17454:2006 | Plastics piping systems Multilayer pipes Test method for the adhesion of the different layers using a pulling rig |
| EN 12117:1997 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| ISO 13951:2015 | Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| ISO 13623:2017 | Petroleum and natural gas industries — Pipeline transportation systems |
| ISO 3503:2015 | Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.