ISO 6721-2:2008
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics Determination of dynamic mechanical properties Part 2: Torsion-pendulum method
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
29-04-2019
Superseded by
Language(s)
English, French
Published date
26-05-2008
Important note : Users cannot be edited or removed once added to your Multi user PDF.
ISO 6721-2:2008 specifies two methods (A and B) for determining the linear dynamic mechanical properties of plastics, i.e. the storage and loss components of the torsional modulus, as a function of temperature, for small deformations within the frequency range from 0,1 Hz to 10 Hz.
The temperature dependence of these properties, measured over a sufficiently broad range of temperatures (for example from -50 C to +150 C for the majority of commercially available plastics), gives information on the transition regions (for example the glass transition and the melting transition) of the polymer. It also provides information concerning the onset of plastic flow. The two methods described are not applicable to non-symmetrical laminates (see ISO 67213, Plastics Determination of dynamic mechanical properties Part 3: Flexural vibration Resonance-curve method). The methods are not suitable for testing rubbers, for which the user is referred to ISO 46642, Rubber, vulcanized or thermoplastic Determination of dynamic properties Part 2: Torsion pendulum methods at low frequencies.
| DevelopmentNote |
Supersedes ISO 537 (04/2001) DRAFT ISO/FDIS 6721-2 is also available for this standard. (12/2017)
|
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
International Organization for Standardization
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 6721-2:2008-09 | Identical |
| NEN EN ISO 6721-2 : 2008 | Identical |
| NS EN ISO 6721-2 : 2ED 2008 | Identical |
| NF EN ISO 6721-2 : 2008 | Identical |
| EN ISO 6721-2:2008 | Identical |
| PN EN ISO 6721-2 : 2011 | Identical |
| SN EN ISO 6721-2 : 2008 | Identical |
| ONORM EN ISO 6721-2 : 2008 | Identical |
| UNE-EN ISO 6721-2:2009 | Identical |
| I.S. EN ISO 6721-2:2008 | Identical |
| BS EN ISO 6721-2:2008 | Identical |
| UNI EN ISO 6721-2 : 2008 | Identical |
| BS 2782-3.342B(1996) : 1996 | Identical |
| UNE 53460-2:1994 | Identical |
| NBN EN ISO 6721-2 : 2008 | Identical |
| UNI EN ISO 6721-1 : 2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| BS EN ISO 6721-1:2011 | Plastics. Determination of dynamic mechanical properties General principles |
| ASTM D 5592 : 1994 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| ONORM EN ISO 11403-1 : 2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| ISO 6721-7:1996 | Plastics Determination of dynamic mechanical properties Part 7: Torsional vibration Non-resonance method |
| EN 13121-1:2003 | GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance conditions |
| DIN EN 14598-2:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements |
| BS EN 13677-2:2003 | Reinforced thermoplastic moulding compounds. Specification for GMT Methods of test and general requirements |
| BS EN 14879-5:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Linings on concrete components |
| DIN EN ISO 8257-2:2006-06 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS 2782-3:Method 323C:1996 | Methods of testing plastics Mechanical properties - Shear vibration. Non-resonance method |
| PREN ISO 11403-1 : DRAFT 2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO/DIS 11403-1:2012) |
| BS ISO 8257-2:1990 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| EN ISO 11403-1:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| UNE-ISO 1268-11:2012 | Fibre-reinforced plastics. Methods of producing test plates. Part 11: Injection moulding of BMC and other long-fibre moulding compounds. Small plates |
| UNE-EN ISO 6721-1:2012 | Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2011) |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
| ISO 1268-11:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates |
| UNE-EN ISO 11403-1:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| DIN EN 15274:2015-06 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| BS EN 14598-2:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements |
| I.S. EN ISO 11403-1:2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| I.S. EN ISO 8257-2:2006 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 15274:2015 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| VDI 3830 Blatt 5:2005-11 | Damping of materials and members - Experimental techniques for the determination of damping characteristics |
| VDI 3830 Blatt 1:2004-08 | Damping of materials and members - Classification and survey |
| 14/30300568 DC : 0 | BS EN 15274 - GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| BS ISO 13781:2017 | Implants for surgery. Homopolymers, copolymers and blends on poly(lactide). In vitro degradation testing |
| BS ISO 1268-11:2005 | Fibre-reinforced plastics. Methods of producing test plates Injection moulding of BMC and other long-fibre moulding compounds. Small plates |
| 18/30356018 DC : DRAFT FEB 2018 | BS ISO 6721-7 - PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 7: TORSIONAL VIBRATION - NON-RESONANCE METHOD |
| BS 2782-3:Method 323D:1996 | Methods of testing plastics Mechanical properties - Torsional vibration. Non-resonance method |
| EN ISO 6721-1:2011 | Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2011) |
| ISO 6721-6:1996 | Plastics Determination of dynamic mechanical properties Part 6: Shear vibration Non-resonance method |
| ISO 17282:2004 | Plastics — Guide to the acquisition and presentation of design data |
| UNI EN ISO 11403-1 : 2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES |
| DIN EN ISO 11403-1:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| BS EN 13121-1:2003 | GRP tanks and vessels for use above ground Raw materials. Specification conditions and acceptance conditions |
| I.S. EN ISO 294-3:2003 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - SMALL PLATES |
| EN ISO 294-3:2003 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002) |
| 12/30255180 DC : 0 | BS EN ISO 11403-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES |
| PREN 15274 : DRAFT 2014 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| 15/30296854 DC : 0 | BS ISO 13781 - INPLANTS FOR SURGERY - HOMOPOLYMERS, COPOLYMERS AND BLENDS ON POLY(LACTIDE) - IN VITRO DEGRADATION TESTING |
| 11/30234454 DC : 0 | BS EN ISO 6721-1 - PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| DIN EN ISO 6721-1:2011-08 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| ASTM D 5592 : 1994 : R2010 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| ISO 6721-1:2011 | Plastics Determination of dynamic mechanical properties Part 1: General principles |
| BS EN ISO 10724-2:2001 | Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Small plates |
| BS EN ISO 294-3:2003 | Plastics. Injection moulding of test specimens of thermoplastic materials Small plates |
| BS EN 13677-3:2003 | Reinforced thermoplastic moulding compounds. Specification for GMT Specific requirements |
| UNE-EN 15274:2015 | General purpose adhesives for structural assembly - Requirements and test methods |
| ISO 8257-2:2001 | Plastics Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
| ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
| ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
| BS EN ISO 8257-2:2006 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 11403-1:2014 | Plastics. Acquisition and presentation of comparable multipoint data Mechanical properties |
| EN 14879-5:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components |
| EN ISO 8257-2:2006 | Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8257-2:2001) |
| EN 13677-3:2003 | Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3: Specific requirements |
| EN 13677-2:2003 | Reinforced thermoplastic moulding compounds - Specification for GMT - Part 2: Methods of test and general requirements |
| EN ISO 10724-2:2000 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates (ISO 10724-2:1998) |
| EN 15274:2015 | General purpose adhesives for structural assembly - Requirements and test methods |
| PREN ISO 6721-1 : DRAFT 2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| BS ISO 11403-1 : AMD 10683 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - MECHANICAL PROPERTIES |
| NF EN ISO 6721-1 : 2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| ISO 13781:2017 | Implants for surgery — Homopolymers, copolymers and blends on poly(lactide) — In vitro degradation testing |
| I.S. EN ISO 6721-1:2011 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| ASTM D 5592 : 1994 : R2002 : EDT 1 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| BS EN 15274:2015 | General purpose adhesives for structural assembly. Requirements and test methods |
| CEN/TR 14548:2003 | Adhesives - Guide to test methods and other standards for the general requirements, characterization and safety of structural adhesives |
| DIN 2874:2002-06 | Flanged steel pipes and flanged steel or cast iron pipes and fittings with PTFE or PFA linings – Technical delivery conditions |
| DIN EN 14879-5:2007-10 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components |
| DIN EN ISO 11403-1:2003-09 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| ISO 6721-1:2011 | Plastics Determination of dynamic mechanical properties Part 1: General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.