Skip to content
Please enter a keyword to search

  • ISO 8605:2001

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Textile-glass-reinforced plastics — Sheet moulding compound (SMC) — Basis for a specification

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  01-03-2024

    Language(s):  English, French

    Published date:  31-05-2001

    Publisher:  International Organization for Standardization

    Add To Cart

    General Product Information - (Show below) - (Hide below)

    Committee ISO/TC 61/SC 13
    Document Type Standard
    Publisher International Organization for Standardization
    Status Superseded
    Superseded By
    Supersedes
    Under Revision

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN EN 14598-3:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
    DIN EN 13421:2006-05 Plastics - Thermoset moulding compounds - Composites and reinforcement fibres - Preparation of specimens for determining the anisotropy of the properties of compression moulding composites
    BS EN ISO 12114:1997 Fibre-reinforced plastics. Thermosetting moulding compounds and prepregs. Determination of cure characteristics
    BS EN 13280:2001 Specification for glass fibre reinforced cisterns of one-piece and sectional construction, for the storage, above ground, of cold water
    BS EN 13421:2006 Plastics. Thermoset moulding compounds. Composites and reinforcement fibres. Preparation of specimens for determining the anisotropy of the properties of compression moulding composites
    ISO 12114:1997 Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of cure characteristics
    BS EN 14598-3:2005 Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements
    EN 13280:2001 Specification for glass fibre reinforced cisterns of one piece and sectional construction, for the storage, above ground, of cold water
    EN ISO 12114 : 1997 FIBRE-REINFORCED PLASTICS - THERMOSETTING MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF CURE CHARACTERISTICS (ISO 12114:1997)
    EN ISO 12115 : 1997 FIBRE-REINFORCED PLASTICS - THERMOSETTING MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF FLOWABILITY, MATURATION AND SHELF LIFE
    EN 14598-3:2005 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
    BS EN ISO 12115:1997 Fibre-reinforced plastics. Thermosetting moulding compounds and prepregs. Determination of flowability, maturation and shelf life
    EN 13421:2006 Plastics - Thermoset moulding compounds - Composites and reinforcement fibres - Preparation of specimens for determining the anisotropy of the properties of compression moulding composites

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
    ISO 11667:1997 Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-fibre and mineral-filler content — Dissolution methods
    ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
    IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
    ISO 1172:1996 Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of the textile-glass and mineral-filler content — Calcination methods
    ISO 3672-1:2000 Plastics Unsaturated-polyester resins (UP-R) Part 1: Designation system
    ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
    ISO 9782:1993 Plastics — Reinforced moulding compounds and prepregs — Determination of apparent volatile-matter content
    IEC 60695-2-12:2010+AMD1:2014 CSV Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials
    IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
    ISO 472:2013 Plastics Vocabulary
    ISO 180:2000 Plastics Determination of Izod impact strength
    ISO 2577:2007 Plastics Thermosetting moulding materials Determination of shrinkage
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
    ISO 1886:1990 Reinforcement fibres Sampling plans applicable to received batches
    ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 3673-1:1996 Plastics Epoxy resins Part 1: Designation
    ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
    ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
    ISO 62:2008 Plastics Determination of water absorption
    ISO 14130:1997 Fibre-reinforced plastic composites — Determination of apparent interlaminar shear strength by short-beam method
    ISO 14126:1999 Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction
    ISO 12114:1997 Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of cure characteristics
    ISO 10352:2010 Fibre-reinforced plastics Moulding compounds and prepregs Determination of mass per unit area
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective