• BS EN 14598-3:2005

    Current The latest, up-to-date edition.

    REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2005

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Requirements
      4.1 General
      4.2 Type and content of filler/reinforcement
      4.3 Recycling
      4.4 Property data
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the requirements for physical and chemical properties of Sheet moulding Compounds (SMC) and Bulk Moulding Compound (BMC) and compression or injection moulded specimens.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/42
    Development Note Supersedes 02/124520 DC (06/2005) Together with BS EN 14598-1 and BS EN 14598-2, it supersedes BS 5734-1(1990), BS 5734-2(1990), BS 5734-3(1990) and BS 5734-4(1990). (07/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    08/30142158 DC : DRAFT NOV 2008 BS 5834-2 - SURFACE BOXES, GUARDS AND UNDERGROUND CHAMBERS FOR GAS AND UTILITIES' PURPOSES - PART 2: SPECIFICATION FOR SURFACE BOXES
    BS 5834-2:2011 Surface boxes, guards and underground chambers for the purposes of utilities Specification for surface boxes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
    IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
    ISO 10350-2:2011 Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics
    ISO 6603-2:2000 Plastics Determination of puncture impact behaviour of rigid plastics Part 2: Instrumented impact testing
    EN ISO 14126:1999/AC:2002 FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF COMPRESSIVE PROPERTIES IN THE IN-PLANE DIRECTION
    EN ISO 8256 : 2004 PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH
    ISO 3167:2014 Plastics Multipurpose test specimens
    ISO 8605:2001 Textile-glass-reinforced plastics Sheet moulding compound (SMC) Basis for a specification
    IEC 60695-2-1:1991 Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance
    ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
    IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
    EN ISO 527-4:1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
    EN ISO 10724-1 : 2001 PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - PART 1: GENERAL PRINCIPLES AND MOULDING OF MULTIPURPOSE TEST SPECIMENS
    ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
    ISO 1172:1996 Textile-glass-reinforced plastics Prepregs, moulding compounds and laminates Determination of the textile-glass and mineral-filler content Calcination methods
    EN ISO 6721-1:2011 PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES
    ISO 2039-1:2001 Plastics Determination of hardness Part 1: Ball indentation method
    EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
    ISO 8256:2004 Plastics Determination of tensile-impact strength
    ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
    EN ISO 2818:1996 PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING
    EN 14598-1 : 2005 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 1: DESIGNATION
    EN 60707 : 1999 FLAMMABILITY OF SOLID NON-METALLIC MATERIALS WHEN EXPOSED TO FLAME SOURCES - LIST OF TEST METHODS
    EN ISO 527-1:2012 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL PRINCIPLES (ISO 527-1:2012)
    EN ISO 10352:2010 FIBRE-REINFORCED PLASTICS - MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF MASS PER UNIT AREA
    EN ISO 179-1:2010 PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST
    EN 60112 : 2003 AMD 1 2009 METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
    ISO 11357-2:2013 Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
    ISO 3795:1989 Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials
    IEC 60167:1964 Methods of test for the determination of the insulation resistance of solid insulating materials
    ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
    IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
    EN ISO 3167:2014 PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014)
    ISO 1268-10:2005 Fibre-reinforced plastics Methods of producing test plates Part 10: Injection moulding of BMC and other long-fibre moulding compounds General principles and moulding of multipurpose test specimens
    ISO 1268-8:2004 Fibre-reinforced plastics Methods of producing test plates Part 8: Compression moulding of SMC and BMC
    IEC 60707:1999 Flammability of solid non-metallic materials when exposed to flame sources - List of test methods
    IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
    EN 60296:2012 FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - UNUSED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEAR (IEC 60296:2012)
    ISO 2577:2007 Plastics Thermosetting moulding materials Determination of shrinkage
    EN ISO 11667 : 1999 FIBRE-REINFORCED PLASTICS - MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF RESIN, REINFORCED-FIBRE AND MINERAL-FILLER CONTENT - DISSOLUTION METHODS
    ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
    EN ISO 2039-1 : 2003 PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD (ISO 2039-1:2001)
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    EN ISO 12115 : 1997 FIBRE-REINFORCED PLASTICS - THERMOSETTING MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF FLOWABILITY, MATURATION AND SHELF LIFE
    EN 14598-2:2005/AC:2006 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
    EN ISO 295 : 2004 PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    EN ISO 6603-2 : 2000 PLASTICS - DETERMINATION OF PUNCTURE IMPACT BEHAVIOUR OF RIGID PLASTICS - PART 2: INSTRUMENTED PUNCTURE TEST (ISO 6603-2:2000)
    EN ISO 10724-2 : 2000 PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - PART 2: SMALL PLATES
    EN ISO 1172 : 1998 TEXTILE-GLASS-REINFORCED PLASTICS - PREPREGS, MOULDING COMPOUNDS AND LAMINATES - DETERMINATION OF THE TEXTILE-GLASS AND MINERAL-FILLER CONTENT - CALCINATION METHODS
    EN 60243-1:2013 ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013)
    EN ISO 14125:1998/A1:2011 FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES
    ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
    EN ISO 4589-2:2017 PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST (ISO 4589-2:2017)
    ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
    EN ISO 291:2008 PLASTICS - STANDARD ATMOSPHERES FOR CONDITIONING AND TESTING
    ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
    EN ISO 179-2:1999/A1:2012 PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - INSTRUMENTED IMPACT TEST (ISO 179-2:1997/AMD 1:2011)
    EN ISO 12114 : 1997 FIBRE-REINFORCED PLASTICS - THERMOSETTING MOULDING COMPOUNDS AND PREPREGS - DETERMINATION OF CURE CHARACTERISTICS (ISO 12114:1997)
    ISO 14126:1999 Fibre-reinforced plastic composites Determination of compressive properties in the in-plane direction
    ISO 1268-11:2005 Fibre-reinforced plastics Methods of producing test plates Part 11: Injection moulding of BMC and other long-fibre moulding compounds Small plates
    ISO 12114:1997 Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of cure characteristics
    ISO 6721-1:2011 Plastics Determination of dynamic mechanical properties Part 1: General principles
    ISO 178:2010 Plastics Determination of flexural properties
    EN ISO 10350-2:2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG FIBRE-REINFORCED PLASTICS
    ISO 10352:2010 Fibre-reinforced plastics Moulding compounds and prepregs Determination of mass per unit area
    EN ISO 175:2010 PLASTICS - METHODS OF TEST FOR THE DETERMINATION OF THE EFFECTS OF IMMERSION IN LIQUID CHEMICALS
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ISO 10724-2:1998 Plastics Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Part 2: Small plates
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective