JIS C 5202:1990
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Test methods of fixed resistors for electronic equipment
31-01-1991
20-06-2002
1 Scope2 Definitions3 Conditions for test 3.1 Standard conditions 3.2 Reference conditions 3.3 Referee conditions 3.4 Drying 3.4.1 Drying conditions 3.4.2 Dry storage 3.4.3 Items to be specificed in detail 3.5 Standard recovery conditions4 Appearance and dimension tests 4.1 Appearance 4.2 Marking 4.3 Dimension5 Electrical performance tests 5.1 Resistance 5.2 Temperature characteristic of resistance and deviation in resistance value 5.3 Voltage coefficient 5.4 Temperature rise 5.5 Short-time overload 5.6 Insulation resistance 5.7 Dielectric withstand voltage 5.8 Intermittent overload 5.9 Noise 5.10 High-frequency characteristic 5.11 Withstand to pulse 5.12 Reactance6 Mechanical performance tests 6.1 Robustness of termination 6.1.1 Equipment 6.1.2 Test method 1 (applicable for resistors other than SMD) 6.1.3 Items to be specified in detail specification 6.1.4 Test method 2 (applicable for SMD) 6.1.5 Items to be specified in detail specification 6.2 Robustness of resistor body 6.2.1 Tests (1) Method 1 (applicable for resistors with a body length exceeding 25 mm) (2) Method 2 (applicable for SMD) 6.3 Resistance to vibration 6.4 Resistance to soldering heat 6.5 Solderability 6.6 Sealing 6.7 Shock 6.8 Radiographic examination 6.9 Resistance to solvent 6.10 Resistance to soldering heat (applicable for SMD) 6.11 Solderability (applicable for SMD) 6.12 Resistance of electrode to soldering damage (applicable for SMD) 6.13 Bump7 Environmental tests 7.1 Resistance to cold 7.2 Resistance to dry heat 7.3 Heat shock 7.4 Change of temperature (cycle) 7.5 Resistance to damp heat (steady state) 7.6 Resistance to damp heat (cyclic) 7.7 Salt mist 7.8 Immersion cycle sealing 7.9 Endurance (under damp and load) 7.10 Endurance (rated load) 7.11 Stability 7.12 Flame retardance 7.13 Climatic sequenceAttached Table 1Annex 1Annex 2
This Japanese Industrial Standard specifies the test methods of fixed resistors principally for use in electronic equipment, hereinafter referred to as \"resistors\". If there is discrepancy between the provision of this specification and that of the relevant detail specification, the provision of the detail specification shall be followed.
| DocumentType |
Standard
|
| PublisherName |
Japanese Standards Association
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| IEC 60115-1:1982 | Identical |
90 [01/11/1990]85
| JIS C 5032:1975 | Sealing (immersion cyclic) testing method for electronic components |
| JIS K 8839:2007 | 2-Propanol (Reagent) |
| JIS B 7502:1994 | Micrometer callipers |
| JIS C 5602:1986 | Glossary of passive components for electronic equipment |
| JIS C 60068-2-13:1989 | Basic environmental testing procedures Part 2: Tests, Test M: Low air pressure Part 2: Tests, Test M: Low air pressure |
| JIS C 5036:1975 | Endurance (electrical) testing method for electronic components |
| JIS B 7507:1993 | Vernier, dial and digital callipers |
| JIS C 60068-1:1993 | Environmental testing Part 1: General and guidance Part 1: General and guidance |
| JIS C 60068-2-17:2001 | Basic environmental testing procedures -- Part 2: Tests -- Test Q: Sealing |
| JIS C 60068-2-11:1989 | Basic environmental testing procedures Part 2: Tests -- Test Ka: Salt mist Part 2: Tests - Test Ka: Salt mist |
| JIS C 6484:2005 | Base materials for printed circuits -- Epoxide woven E-glass laminated sheet of defined flammability (vertical burning test) |
| JIS Z 3282:2006 | Soft solders -- Chemical compositions and forms |
| JIS C 60068-2-21:2002 | Environmental testing -- Part 2-21: Tests -- Test U: Robustness of termination and integral mounting devices Part 2-21: Tests - Test U: Robustness of termination and integral mounting devices |
| JIS C 60068-2-45:1995 | Environmental testing procedures of electronic and electrical resistance to solvents (immersion in cleaning solvents) |
| JIS C 60068-2-20:1996 | Basic environmental testing procedures Part 2: Tests. Test T: Soldering Part 2: Tests. Test T: Soldering |
| JIS C 5602:1986 | Glossary of passive components for electronic equipment |
| JIS C 6401:1991 | Fixed wire wound resistors -- Power type |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.