MIL-C-28809 Revision B:1988
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
CIRCUIT CARD ASSEMBLIES, RIGID, FLEXIBLE & RIGID FLEX
21-04-1995
Important note : Users cannot be edited or removed once added to your Multi user PDF.NO CONTENTS SECTION
Specifies circuit card assemblies, consisting of printed wiring boards with separately manufactured parts added. Coverage includes type of board, number of layers, part mounting, rigid boards, storage, solderability, solder, fluxes, conformal coating, buffer material, wires, component mounting, conductive areas, spacing, electrical spacing, clearance, and stress relief bends.
| DocumentType |
Standard
|
| Pages |
49
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Withdrawn
|
| Supersedes |
| MIL-R-2729 Revision D:1992 | REGULATOR EXCITER SYSTEMS, VOLTAGE, A.C. GENERATOR, NAVAL SHIPBOARD USE |
| MIL E 917 : E | ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS (NAVAL SHIPBOARD USE) |
| MIL-STD-1861 Revision A:1993 | ELECTRICAL & ELECTRONIC ASSEMBLIES, BOARDS, CARDS, AND ASSOCIATED HARDWARE, SELECTION AND USE OF |
| PPP-C-1752 Revision D:1989 | CUSHIONING MATERIAL, PACKAGING, POLYETHYLENE FOAM |
| DOD STD 2000/3 : A NOTICE 1 | CRITERIA FOR HIGH QUALITY/HIGH RELIABILITY SOLDERING TECHNOLOGY |
| IPC S 815 : B1987 | GENERAL REQUIREMENTS FOR SOLDERING OF ELECTRONIC INTERCONNECTIONS |
| MIL-STD-2118 Base Document:1984 | FLEXIBLE AND RIGID FLEX PRINTED WIRING FOR ELECTRONIC EQUIPMENT DESIGN REQUIREMENTS FOR |
| IPC T 50 : M | TERMS AND DEFINITIONS FOR INTERCONNECTING AND PACKAGING ELECTRONIC CIRCUITS |
| MIL-B-117G:1993 | BAG, SLEEVE AND TUBING |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| MIL-STD-130 Revision N:2007 | IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY |
| PPP-B-636 Revision J:1981 | BOX, SHIPPING, FIBERBOARD |
| MIL-STD-147 Revision E:2008 | PALLETIZED UNIT LOADS |
| MIL-STD-810 Revision G:2008 | ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS |
| PPP-B-566 Revision E:1974 | BOX, FOLDING, PAPERBOARD |
| DOD-STD-2000-4 Revision A:1987 | GENERAL PURPOSE SOLDERING REQUIREMENT FOR ELECTRICAL AND ELECTRONIC EQUIPMENT |
| MIL-STD-275 Revision E:1984 | PRINTED WIRING - ELECTRONIC EQUIPMENT |
| IPC CC 830 : B | QUALIFICATION AND PERFORMANCE OF ELECTRICAL INSULATING COMPOUND FOR PRINTED WIRING ASSEMBLIES |
| MIL-I-46058 Revision C:1972 | Insulating Compound, Electrical (for Coating Printed Circuit Assemblies) |
| DOD STD 1686 : 0 | ELECTROSTATIC DISCHARGE CONTROL PROGRAM FOR PROTECTION OF ELECTRICAL AND ELECTRONIC PARTS ASSEMBLIES AND EQUIPMENT (EXCLUDING ELECTRICALLY INITIATED EXPLOSIVE DEVICES)(METRIC) |
| MIL-STD-45662 Revision A:1988 | CALIBRATION SYSTEMS REQUIREMENTS |
| QQ-S-781 Revision H:1974 | STRAPPING, STEEL, AND SEALS |
| DOD-STD-2000-1 Revision B:1986 | SOLDERING TECHNOLOGY, HIGH QUALITY/HIGH RELIABILITY |
| IPC TM 650 : 0 | TEST METHODS MANUAL |
| PPP-C-1797 Revision A:1982 | CUSHIONING MATERIAL, RESILIENT, LOW DENSITY, UNICELLULAR POLYPROPYLENE FOAM |
| PPP-C-795 Revision D:1994 | Cushioning Material, Closed Cell Flexible, Plastic Film |
| IPC S 805 : 1985 | PRINTED CIRCUITS - SOLDERABILITY TEST FOR COMPONENT LEADS AND TERMINATIONS, |
| PPP-B-676 Revision E:1992 | BOXES SET-UP |
| QQ-S-571 Revision F:1994 | SOLDER, ELECTRONIC (96 TO 485 DEGREES C) |
| MIL-STD-794 Revision E:1982 | PART AND EQUIPMENT, PROCEDURES FOR PACKAGING AND PACKING OF |
| MIL-P-116 Revision J:1988 | PRESERVATION, METHODS OF |
| PPP-B-601 Revision H:1989 | BOXES, WOOD, CLEATED PLYWOOD |
| MIL-F-14256 Revision F:1993 | FLUX, SOLDERING, LIQUID (ROSIN BASE) |
| MIL-STD-202 Revision H:2015 | ELECTRONIC AND ELECTRICAL COMPONENT PARTS |
| QQ-W-343 Revision G:1997 | WIRE, ELECTRICAL, COPPER (UNINSULATED) |
| MIL P 55110 : LATEST | PRINTED WIRING BOARD, RIGID GENERAL SPECIFICATION FOR |
| PPP-B-621 Revision D:1981 | BOXES, WOOD, NAILED AND LOCK CORNER |
| PPP-C-1842 Revision B:1992 | CUSHIONING MATERIAL, PLASTIC, OPEN CELL (FOR PACKAGING APPLICATIONS) |
| DOD-STD-2000-2 Revision A:1986 | PART AND COMPONENT MOUNTING FOR HIGH QUALITY/HIGH RELIABILITY SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| MIL-STD-105 Revision E:1989 | SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES |
| MIL P 50884 : E | PRINTED WIRING BOARD, FLEXIBLE OR RIGID-FLEX, GENERAL SPECIFICATION FOR |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.