MIL-DTL-32408 Base Document:2012
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
INTEGRAL MOTOR PUMP (IMP)
02-05-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
Specifies vertical or horizontal centrifugal Integral Motor Pumps (IMP) for shipboard applications on U.S. Navy ships and submarines. Pumps are to be sealless and configured for either end suction where impeller is overhung with all bearings on one side of the impeller, or in an inline configuration with the impeller positioned between two sets of bearings.
| Committee |
FSC 4320
|
| DevelopmentNote |
NOTICE 1 - Notice of Validation. (11/2016) NOTICE 2 - Notice of Cancellation without Replacement. (07/2017)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Withdrawn
|
| NEMA MW 1000 : 2016 | MAGNET WIRE |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| QQ-N-286 Revision G:2000 | NICKEL-COPPER ALUMINUM ALLOY, WROUGHT (UNS N05500) |
| MIL-STD-740-1 Base Document:1986 | AIRBORNE SOUND MEASUREMENTS AND ACCEPTANCE CRITERIA OF SHIPBOARD EQUIPMENT |
| HI 1.6 : 2000 | CENTRIFUGAL PUMP TESTS |
| MIL E 917 : E | ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS (NAVAL SHIPBOARD USE) |
| ASTM B 473 : 2007 | Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire |
| DOD-STD-1399-301 Revision A:1986 | INTERFACE STANDARD FOR SHIPBOARD SYSTEMS SECTION 301A SHIP MOTION AND ATTITUDE (METRIC) |
| ASTM B 584 : 2014 : REDLINE | Standard Specification for Copper Alloy Sand Castings for General Applications |
| IEC TS 61934:2011 | Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses |
| HI 9.1 - 9.5 : 2015 | PUMPS - GENERAL GUIDELINES |
| MIL-DTL-1222 Revision J:2000 | STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR |
| MIL-STD-1687 Revision A:1987 | THERMAL SPRAY PROCESSES FOR NAVAL SHIP MACHINERY AND ORDNANCE APPLICATIONS |
| MIL-DTL-17060 Revision G:2009 | MOTORS, ALTERNATING CURRENT, INTEGRAL-HORSEPOWER, SHIPBOARD USE |
| MIL-HDBK-454 Revision B:2007 | GENERAL GUIDELINES FOR ELECTRONIC EQUIPMENT |
| IEC TS 60034-18-41:2006 | Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters |
| ASTM D 5363 : 2016 : REDLINE | Standard Specification for Anaerobic Single-Component Adhesives (AN) |
| NAVSEA T9074 AS GIB 010/271 : 0 | REQUIREMENTS FOR NONDESTRUCTIVE TESTING METHODS |
| MIL-STD-740-2 Base Document:1986 | STRUCTURE BORNE VIBRATORY ACCELERATION MEASUREMENTS ACCEPTANCE CRITERIA OF SHIPBOARD EQUIPMENT |
| NAVSEA S9074 AR GIB 010/278 : 0 | REQUIREMENTS FOR FABRICATION WELDING AND INSPECTION, AND CASTING INSPECTION AND REPAIR FOR MACHINERY, PIPING, AND PRESSURE VESSELS |
| FED-STD-H28-2 Revision B:1991 | Screw-Thread Standards for Federal Services Section 2 Unified Inch Screw Threads- UN and UNR Thread Forms |
| ANSI S2.19 : 0 | MECHANICAL VIBRATION - BALANCE QUALITY REQUIREMENTS OF RIGID ROTORS - PART 1: DETERMINATION OF PERMISSIBLE RESIDUAL UNBALANCE, INCLUDING MARINE APPLICATIONS |
| ASTM B 61 : 2015 : REDLINE | Standard Specification for Steam or Valve Bronze Castings |
| MIL-STD-882 Revision E:2012 | System Safety |
| MIL-STD-461 Revision G:2015 | REQUIREMENTS FOR THE CONTROL OF ELECTROMAGNETIC INTERFERENCE CHARACTERISTICS OF SUBSYSTEMS AND EQUIPMENT |
| MIL-STD-777 Revision F:2012 | SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS |
| IEEE 115-2009 REDLINE | IEEE Guide for Test Procedures for Synchronous Machines Part I—Acceptance and Performance Testing Part II—Test Procedures and Parameter Determination for Dynamic Analysis |
| MIL S 901 : D | SHOCK TESTS, HI [HIGH IMPACT] SHIPBOARD MACHINERY, EQUIPMENT AND SYSTEMS, REQUIREMENTS FOR |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| MIL-PRF-32168 Base Document:2004 | VARIABLE SPEED DRIVE SYSTEM FOR INDUCTION AND SYNCHRONOUS MACHINES |
| MIL-STD-1474 Revision E:2015 | NOISE LIMITS |
| HI 1.1 - 1.2 : 2014 | ROTODYNAMIC CENTRIFUGAL PUMPS FOR NOMENCLATURE AND DEFINITIONS |
| MIL-DTL-15024 Revision F:1997 | Plates and Tags for Identification of Equipment, General Specification for |
| FED-STD-H28 Revision A:1994 | Screw-Thread Standards for Federal Services |
| MIL-DTL-15090 Revision E:2010 | ENAMEL, EQUIPMENT, LIGHT GRAY, (NAVY FORMULA NO. 111) |
| MIL-PRF-20042 Revision F:2015 | FLANGES, PIPE, BRONZE (SILVER BRAZING) |
| MIL-STD-167-1 Revision A:2005 | MECHANICAL VIBRATIONS OF SHIPBOARD EQUIPMENT (TYPE 1 - ENVIRONMENTAL AND TYPE 2 - INTERNALLY EXCITED) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.