NF EN 60439-1 : 2000 AMD 1 2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1: TYPE-TESTED AND PARTIALLY TYPE-TESTED ASSEMBLIES
01-02-2015
12-01-2013
1 Généralités
2 Définitions
3 Classification des ENSEMBLES
4 Caractéristiques électriques des ENSEMBLES
5 Renseignements à donner sur l'ENSEMBLE
6 Conditions d'emploi
7 Dispositions constructives
8 Prescriptions concernant les essais
Annexe A (normative) Valeurs minimales et maximales des
sections des conducteurs de cuivre
convenant au raccordement
(voir 7.1.3.2)
Annexe B (normative) Méthode pour calculer la section des
conducteurs de protection sous
l'aspect des contraintes thermiques
causées par les courants de courte
durée (pour plus de détails voir
la CEI 60364-5-54)
Annexe C (informative) Exemples représentatifs d'ENSEMBLES
Annexe D (informative) Dispositions de séparations
intérieures (voir 7.7)
Annexe E (informative) Sujets soumis à un accord entre le
constructeur et l'utilisateur
Annexe F (normative) Mesure des lignes de fuite et des
distances d'isolement
Annexe G (normative) Correspondance entre la tension
nominale du réseau d'alimentation
et la tension assignée de tenue aux
chocs des matériels
Bibliographie
Annexe ZA (normative) Autres publications internationales
citées dans la présente norme avec
les références des publications
européennes correspondantes
Annexe ZB (informative)
Applies to low-voltage switchgear and controlgear ASSEMBLIES (type-tested ASSEMBLIES (TTA) and partially type-tested ASSEMBLIES (PTTA)), the rated voltage of which does not exceed 1000 V a.c. at frequencies not exceeding 1000 Hz, or 1500 V d.c.
| DevelopmentNote |
Indice de classement: C63-421. Supersedes NFC 63 421. (09/2004)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| UNE-EN 60439-1:2001 | Identical |
| BS EN 60439-1:1999 | Identical |
| IEC 60439-1:1999+AMD1:2004 CSV | Identical |
| EN 60439-1:1999/A1:2004 | Identical |
| I.S. EN 60439-1:2000 | Identical |
| DIN EN 60439-1 : 2005 | Identical |
| NF ISO 8528-4 : 2005 | RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR |
| NFF 48 130 : 1998 | MODULAR POWER SUPPLY UNITS FOR SYSTEMS FOR SIGNALLING EQUIPMENT, TELECOMMUNICATIONS EQUIPMENT AND COMPUTER EQUIPMENT - CONVECTOR MODULE |
| UTEC 15 500 : 2003 | DETERMINATION OF CROSS-SECTIONAL AREA OF CONDUCTORS AND SELECTION OF PROTECTIVE DEVICES WITH SOFTWARES |
| NF EN 62310-3 : 2008 | STATIC TRANSFER SYSTEMS (STS) - PART 3: METHOD FOR SPECIFYING THE PERFORMANCE AND TEST REQUIREMENTS |
| NF EN 50512 : 2009 | ELECTRICAL INSTALLATIONS FOR LIGHTING AND BEACONING OF AERODROMES - ADVANCED VISUAL DOCKING GUIDANCE SYSTEMS (A-VDGS) |
| NF EN 50490 : 2009 | ELECTRICAL INSTALLATIONS FOR LIGHTING AND BEACONING OF AERODROMES - TECHNICAL REQUIREMENTS FOR AERONAUTICAL GROUND LIGHTING CONTROL AND MONITORING SYSTEMS - UNITS FOR SELECTIVE SWITCHING AND MONITORING OF INDIVIDUAL LAMPS |
| NF EN 61851-22 : 2002 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: A.C. ELECTRIC VEHICLE CHARGING STATION |
| UTEC 15 443 : 2004 | PROTECTION OF LOW-VOLTAGE ELECTRICAL INSTALLATIONS AGAINST OVER VOLTAGES OF ATMOSPHERIC DISCHARGES AND SWITCHING - SELECTION AND ERECTION OF SURGE PROTECTIVE DEVICES |
| NF EN 62040-1-2 : 2004 | |
| NF EN 60947-7-2 : 2009 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-2: ANCILLARY EQUIPMENT - PROTECTIVE CONDUCTOR TERMINAL BLOCKS FOR COPPER CONDUCTORS |
| NF EN 50300 : 2004 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - GENERAL REQUIREMENTS FOR LOW-VOLTAGE SUBSTATION CABLE DISTRIBUTION BOARDS |
| NF EN 61921 : 2003 | POWER CAPACITORS - LOW VOLTAGE POWER FACTOR CORRECTION BANKS |
| NF EN 60947-1 : 2007 AMD 2 2015 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES |
| NF EN 1218-2 : 2004 + A1 2010 | SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 2: DOUBLE END TENONING AND/OR PROFILING MACHINES FED BY CHAIN OR CHAINS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.