PD ISO/TS 17165-2:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Hydraulic fluid power. Hose assemblies Practices for hydraulic hose assemblies
Hardcopy , PDF
10-04-2018
English
30-04-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Safety considerations
5 Hose selection and routing
6 Hose assembly fabrication
7 Hose installation and replacement
8 Maintenance inspection
9 Storage
10 Identification statement (reference to this part
of ISO 17165)
Annex A (informative) - Examples of actual failure
resulting from improper use
Specifies guidelines for selection, routing, fabrication, installation, replacement, maintenance and storage of hose and hose assemblies for hydraulic fluid power systems which are manufactured from hoses conforming to ISO 1436, ISO 3862, ISO 3949, ISO 4079 and ISO 11237, and hose fittings conforming to ISO 12151-1 to ISO 12151-6.
| Committee |
MCE/18/-/4
|
| DevelopmentNote |
Supersedes BS PD ISO/TR 17165-2. (05/2013)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO/TS 17165-2:2013 | Identical |
| ISO 3862:2017 | Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 17165-1:2007 | Hydraulic fluid power — Hose assemblies — Part 1: Dimensions and requirements |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| ISO 3949:2009 | Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| ISO 12151-2:2003 | Connections for hydraulic fluid power and general use — Hose fittings — Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24 degree cone connector ends with O-rings |
| ISO 2230:2002 | Rubber products — Guidelines for storage |
| ISO 8331:2016 | Rubber and plastics hoses and hose assemblies Guidelines for selection, storage, use and maintenance |
| ISO 6162-2:2012 | Hydraulic fluid power Flange connections with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76 |
| ISO 8330:2007 | Rubber and plastics hoses and hose assemblies Vocabulary |
| ISO 12151-5:2007 | Connections for hydraulic fluid power and general use — Hose fittings — Part 5: Hose fittings with ISO 8434-2 37 degree flared ends |
| ISO 8434-2:2007 | Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors |
| ISO 4079:2017 | Rubber hoses and hose assemblies Textile-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 12151-3:2010 | Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
| ISO 8434-3:2005 | Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors |
| ISO 6162-1:2012 | Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 |
| ISO 8434-6:2009 | Metallic tube connections for fluid power and general use — Part 6: 60 degree cone connectors with or without O-ring |
| ISO 11237:2017 | Rubber hoses and hose assemblies — Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids — Specification |
| ISO 3457:2003 | Earth-moving machinery — Guards — Definitions and requirements |
| ISO 8434-4:1995 | Metallic tube connections for fluid power and general use Part 4: 24 degree cone connectors with O-ring weld-on nipples |
| ISO 12151-1:2010 | Connections for hydraulic fluid power and general use — Hose fittings — Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends |
| ISO 12151-6:2009 | Connections for hydraulic fluid power and general use Hose fittings Part 6: Hose fittings with ISO 8434-6 60 degree cone ends |
| ISO 12151-4:2007 | Connections for hydraulic fluid power and general use Hose fittings Part 4: Hose fittings with ISO 6149 metric stud ends |
| ISO 1436:2017 | Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 6149:1980 | Fluid power systems and components Metric ports Dimensions and design |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.