PREN 13000 : DRAFT 2009

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Safety requirements and/or protective measures
  4.1 Structures and components
  4.2 Equipment and devices
  4.3 Visibility
  4.4 Noise and noise reduction
  4.5 Fire protection
  4.6 Requirements for transport and travel
  4.7 Roll over and tip over protection
5 Verification
  5.1 Methods of verification
  5.2 Test procedures and conditions
  5.3 Verification based on noise emission values
6 Information for use
  6.1 Format of instruction
  6.2 Instructions for use
  6.3 Instructions for assembly, erection, disassembly
       and transport
  6.4 Instructions for maintenance and inspection
  6.5 Instructions for training
  6.6 Instructions for spare parts
  6.7 Instructions for disposal
7 Marking
  7.1 Machine marking
  7.2 Information and warning
  7.3 Graphic symbols
  7.4 Marking of crane parts
  7.5 Marking of outriggers
  7.6 Marking data recorder
Annex A (normative) - Examples of mobile crane types
Annex B.1 (informative) - Major parts of telescopic cranes
Annex B.2 (informative) - Major parts of lattice jib cranes
Annex C (normative) - List of hazards
Annex D (normative) - Load effects of combined motions
Annex E (normative) - Crane operator's seat dimensions
  E.1 General
  E.2 Dimensions of crane operator's seat
  E.3 Other dimensions or adjustments
Annex F (normative) - Rigid body stability: Load effects due
        to acceleration
Annex G.1 (normative) - Noise test code for mobile cranes
  G.1.1 Introduction
  G.1.2 Normative references
  G.1.3 Terms and definitions
  G.1.4 Description of machinery family
  G.1.5 Sound power level determination
  G.1.6 Emission sound pressure level determination
  G.1.7 Configuration
  G.1.8 Operating conditions
  G.1.9 Information on measurement uncertainties
  G.1.10 Information to be recorded
  G.1.11 Information to be reported
  G.1.12 Declaration and verification of noise emission values
Annex G.2 (normative) - Noise measurement, test report
  G.2.1 General data
  G.2.2 Measurements per motion
Annex H (normative) - Limit values for structural and fine
        grain steel types
Annex J.1 (normative) - Minimum requirements for specification
          of hoist/derrick gears
Annex J.2 (normative) - Minimum requirements for specification
          of slewing gears
Annex J.3 (normative) - Minimum requirements for specification
          of travel gears
Annex J.4 (normative) - Minimum requirements for specification
          of drums
Annex K.1 (normative) - Minimum requirements for the
          specification of lifting hooks
Annex K.2 (normative) - Minimum requirements for specification
          of sheaves
Annex K.3 (normative) - Minimum requirements for specification
          of hook blocks
Annex K.4 (normative) - Minimum requirements for the specification
          of hydraulic cylinders
Annex K.5 (normative) - Minimum requirements for the specification
          of slew rings
Annex L (normative) - Proof of competence
  L.1 General
  L.2 Proof of competence for steel structures
  L.3 Proof of competence for non steel structures
  L.4 Proof of competence for load bearing components
  L.5 Proof of competence of rigid body stability of the crane
  L.6 Proof of competence - experimental
Annex M (normative) - Test of steering systems for off-road
        mobile cranes
  M.1 Test conditions
  M.2 Test procedure
  M.3 Permitted steering control effort
Annex N.1 (informative) - Wind speed as a function of elevation
Annex N.2 (informative) - Impact pressure as a function of
          elevation
Annex N.3 (informative) - Storm wind map of Europe
Annex P (normative) - Efficiency of sheave sets
Annex Q (informative) - Manufacturer's sign
Annex R (normative) - Certificate for wire rope, requirements
Annex S (normative) - Certificate for chain, requirements
Annex T (informative) - Test procedures: Selection of load cases
Annex U (normative) - Test certificate
Annex V (informative) - Additional information of the concept of
        the limiting and indicating device
Annex W (informative) - Selection of a suitable set of crane
        standards for a given application
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of EU Directive
         98/37/EC
Annex ZB (informative) - Relation between this European Standard
         and the Essential Requirements of EU Directive 2006/42/EC
Bibliography

Describes the design, construction, installation of safety devices, information for use, maintenance and testing of mobile cranes as defined in ISO 4306-2 with the exception of loader cranes.