PREN 54-3 : DRAFT 2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
23-07-2014
12-01-2013
Foreword
1 Scope
2 Normative references
3 Definitions and abbreviations
3.1 Definitions
3.2 Abbreviations
4 Requirements
4.1 Compliance
4.2 Sound level
4.3 Frequency and sound pattern
4.4 Requirements for voice sounders
4.5 Construction
4.6 On-site adjustment of the mode of
operation
4.7 Durability
4.8 Marking and data
4.9 Additional requirements for software
controlled sounders
5 Tests
5.1 General
5.2 Reproducibility
5.3 Operational performance
5.4 Durability
5.5 Dry heat (operational)
5.6 Dry heat (endurance)
5.7 Cold (operational)
5.8 Damp heat, cyclic (operational)
5.9 Damp heat, steady state (endurance)
5.10 Damp heat, cyclic (endurance)
5.11 Sulfur dioxide (SO[2]) corrosion
(endurance)
5.12 Shock (operational)
5.13 Impact (operational)
5.14 Vibration, sinusoidal (operational)
5.15 Vibration, sinusoidal (endurance)
5.16 Electromagnetic compatibility (EMC),
immunity (operational)
5.17 Enclosure protection
5.18 Operational performance for voice
sounders
5.19 Voice sounders sequence timing
5.20 Voice sounders message synchronization
Annex A (normative) - Sound level for fire alarm
Sounders
A.1 General
A.2 Mounting arrangements
A.3 Instrumentation
A.4 Background noise level
A.5 Measurement of sound level
Annex B (normative) - Comparative sound level test
during environmental conditioning
B.1 General
B.2 Test chamber
B.3 Mounting arrangements
B.4 Instrumentation
B.5 Background noise level
B.6 Test procedure
Annex C (informative) - Sound patterns recommended
or required in some European countries
C.1 Introduction
C.2 Standards references
C.3 Information on sound patterns
Annex D (informative) - Comparison of flammability test
requirements in various standards
D.1 Introduction
D.2 Relevant standards
D.3 Vertical burning tests
Annex ZA (informative) - Clauses addressing the provisions
of the EU Construction Products Directive (89/106/EEC)
ZA.1 Scope and relevant clauses
ZA.2 Procedures for the attestation of conformity
of control and indicating equipment covered
by this standard
ZA.3 CE marking and labelling and accompanying
documentation
ZA.4 EC certificate and declaration of conformity
Describes the requirements, test methods and performance criteria for fire alarm sounders in a fixed installation intended to signal an audible warning of fire detection and fire alarm systems and the occupants of a building.
| Committee |
TC 72
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 09/30184483 DC : 0 | Identical |
| VDI 6010 Blatt 2:2011-05 | Technical safety installations - Automation and control of fire protective services |
| IEC 60695-11-20:2015 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
| EN 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| EN 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| EN 60068-2-27:2009 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| EN 61672-1:2013 | Electroacoustics - Sound level meters - Part 1: Specifications |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 9001:2015 | Quality management systems — Requirements |
| IEC 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
| EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 50130-4:2011/A1:2014 | ALARM SYSTEMS - PART 4: ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD: IMMUNITY REQUIREMENTS FOR COMPONENTS OF FIRE, INTRUDER, HOLD UP, CCTV, ACCESS CONTROL AND SOCIAL ALARM SYSTEMS |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| EN 54-1:2011 | Fire detection and fire alarm systems - Part 1: Introduction |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.