Skip to content
Please enter a keyword to search
  • Preview

    S.R. CEN TS 15534-3:2007

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    WOOD-PLASTICS COMPOSITES (WPC) - PART 3: CHARACTERISATION OF WPC PRODUCTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-02-2014

    Language(s):  English

    Published date:  01-01-2007

    Publisher:  National Standards Authority of Ireland

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Characterisation of WPC products
    Annex A (informative) Technical data templates

    Abstract - (Show below) - (Hide below)

    Describes the required and optional properties of wood-plastics composite (WPC) products. It is intended to be used as a basis for the specifications of WPC products.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 7724-1:1984 Paints and varnishes Colorimetry Part 1: Principles
    ISO 6603-2:2000 Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing
    EN 321:2001 Wood-based panels - Determination of moisture resistance under cyclic test conditions
    EN ISO 9142:2003 Adhesives - Guide to the selection of standard laboratory ageing conditions for testing bonded joints (ISO 9142:2003)
    EN 310:1993 Wood-based panels - Determination of modulus of elasticity in bending and of bending strength
    ENV 1156:1998 Wood-based panels - Determination of duration of load and creep factors
    EN 317:1993 Particleboards and fibreboards - Determination of swelling in thickness after immersion in water
    EN 13446:2002 Wood-based panels - Determination of withdrawal capacity of fasteners
    ISO 7724-2:1984 Paints and varnishes Colorimetry Part 2: Colour measurement
    ISO 11925-2:2010 Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test
    ISO 9142:2003 Adhesives Guide to the selection of standard laboratory ageing conditions for testing bonded joints
    EN 789:2004 Timber structures - Test methods - Determination of mechanical properties of wood based panels
    EN ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010)
    EN 1383:2016 Timber structures - Test methods - Pull through resistance of timber fasteners
    EN 13823:2010+A1:2014 REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
    ISO 7724-3:1984 Paints and varnishes Colorimetry Part 3: Calculation of colour differences
    EN ISO 9239-1:2010 Reaction to fire tests for floorings - Part 1: Determination of the burning behaviour using a radiant heat source (ISO 9239-1:2010)
    EN 13893:2002 Resilient, laminate and textile floor coverings - Measurement of dynamic coefficient of friction on dry floor surfaces
    EN ISO 4628-6:2011 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 6: Assessment of degree of chalking by tape method (ISO 4628-6:2011)
    EN ISO 6603-2:2000 Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture test (ISO 6603-2:2000)
    EN 318:2002 Wood based panels - Determination of dimensional changes associated with changes in relative humidity
    ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
    ISO 877:1994 Plastics Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified weathering by daylight using Fresnel mirrors
    ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
    ISO 4628-6:2011 Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 6: Assessment of degree of chalking by tape method
    CEN/TS 15534-1:2007 Wood-plastics composites (WPC) - Part 1: Test methods for characterisation of WPC materials and products
    CEN/TS 15534-2:2007 Wood-plastics composites (WPC) - Part 2: Characterisation of WPC materials
    EN ISO 877 : 1996
    ISO 9239-1:2010 Reaction to fire tests for floorings Part 1: Determination of the burning behaviour using a radiant heat source
    EN 927-6:2006 Paints and varnishes - Coating materials and coating systems for exterior wood - Part 6: Exposure of wood coatings to artificial weathering using fluorescent UV lamps and water
    EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
    EN ISO 11925-2:2010/AC:2011 REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
    ISO 2813:2014 Paints and varnishes — Determination of gloss value at 20°, 60° and 85°
    EN ISO 2813:2014 Paints and varnishes - Determination of gloss value at 20°, 60° and 85° (ISO 2813:2014)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective