SAE AMS7259E
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Rubber: Fluorocarbon (FKM) High Temperature/Fluid Resistant Low Compression Set/85 to 95 Hardness For Seals In Fuel Systems and Specific Engine Oil Systems
Hardcopy , PDF
English
20-05-2013
25-09-2024
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
Describes a fluorocarbon (FKM) rubber in the form of O-rings, O-ring cord, compression seals, and molded-in-place gaskets for aeronautical and aerospace applications.
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This specification covers a fluorocarbon (FKM) rubber in the form of O-rings, O-ring cord, compression seals, and molded-in-place gaskets for aeronautical and aerospace applications.
| SAE AIR1387D | Designing with Elastomers for use at Low Temperatures, Near or Below Glass Transition |
| SAE AS19692B | Aerospace – Military Type Variable Delivery, Pressure Compensated Hydraulic Pump |
| SAE AMS3218D | Elastomer: Fluorocarbon (FKM) Rubber High-Temperature-Fluid Resistant Low Compression Set 85 to 95 |
| MIL-DTL-17060 Revision G:2009 | Motors, Alternating Current, Integral-Horsepower, Shipboard Use |
| ASTM F 1511 : 2016-11 | SPECIFICATION FOR MECHANICAL SEALS FOR SHIPBOARD PUMP APPLICATIONS |
| SAE ARP5796 | Flight Critical Control Valves, Military Aircraft |
| MIL-DTL-24509 Revision B:2017 | Valves, Flanged, Balland Plugfor Sewageand Seawater Service |
| MIL-STD-1587 Revision D:2017 | Material and Process Requirements for Aerospace Weapons Systems |
| MIL-DTL-24231 Revision E:2013 | Connectors, Plugs, Receptacles, Adapters, Hull Inserts, and Hull Insert Plugs, Pressure-Proof, General Specification for |
| SAE AIR786B | Elastomer Compatibility Considerations Relative to Elastomeric Sealant Selection |
| MIL-G-18997 Revision E:1991 | GAUGE, PRESSURE, DIAL INDICATING |
| ASME B40.100 : 2013 | Pressure Gauges and Gauge Attachments (B40.100 - 2013) |
| MIL-PRF-81975 Revision C:2008 | Couplings, Regulated, Aerial Pressure Refueling Type MA-2, Type MA-3 and Type MA-4 |
| MIL-PRF-39012-79 Revision G:2008 | Connectors, Plug, Electrical, Coaxial, Radio Frequency, Series SMA (Cabled) Pin Contact, Class 2, Semirigid Cable |
| SAE AS4941B | Aerospace - General Requirements for Commercial Aircraft Hydraulic Components |
| MIL-PRF-57267 Base Document:2017 | Coupling, Aerial Pressure Refueling Type MA-5 |
| MIL-DTL-7899 Revision D:2014 | Valve, Check, Aircraft Fuel System |
| MIL-PRF-39012-80 Revision F:2008 | Connectors, Plug, Electrical, Coaxial, Radio Frequency, Series SMA (Cabled) Pin Contact, Right Angle, Class 2, Semirigid Cable |
| MIL-DTL-22606 Revision D:2011 | Flask and End Plugs, Compressed Gas - Air, Oxygen and Nitrogen |
| MIL-DTL-24578 Revision C:2015 | Valves, Globe, Pressure Instrument, Stem Test Connection, Union End |
| MIL-STD-1568 Revision D:2015 | Materials and Processes for Corrosion Prevention and Control in Aerospace Weapons Systems |
| MIL-STD-777 Revision F:2012 | Schedule of Piping, Valves, Fittings, and Associated Piping Components for Naval Surface Ships |
| ASTM D 297 : 2015 : REDLINE | Standard Test Methods for Rubber Products—Chemical Analysis |
| SAE AMS2817G | Packaging and Identification of Molded Elastomeric Seals and Sealing Components |
| SAE AS3581 | PACKING, PREFORMED – O-RING SEAL AMS7259 |
| ASTM D 1414 : 2015 : REDLINE | Standard Test Methods for Rubber O-Rings |
| SAE AS568D | Aerospace Size Standard for O-rings |
| SAE AIR851C | O-Ring Tension Testing Calculations |
| ISO 3601-1:2012 | Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes |
| ASTM D 1329 : 2016 : REDLINE | Standard Test Method for Evaluating Rubber Property—Retraction at Lower Temperatures (TR Test) |
| ISO 3601-3:2005 | Fluid power systems — O-rings — Part 3: Quality acceptance criteria |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.