SAE AS 4459 : 2013
Current
Current
The latest, up-to-date edition.
FITTINGS, TUBE, FLUID SYSTEM 3000 PSIG (21000 KPA) RATED PRESSURE, EXTERNALLY SWAGED, SPECIFICATION FOR
Published date
15-03-2013
Publisher
Sorry this product is not available in your region.
1 SCOPE
2 APPLICABLE DOCUMENTS
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 NOTES
This SAE Aerospace Standard (AS) establishes the requirements for externally swaged tube-fitting assemblies used in aircraft fluid systems in the following pressure classes: B (1500 psi or 10 500 kPa), and D (3000 psi or 21 000 kPa), and in temperature types I (−65 to 160 °F or −55 to 70 °C), and II (−65 to 275 °F or −55 to 135 °C) of AS2001.
| Committee |
G-3
|
| DocumentType |
Revision
|
| PublisherName |
SAE International
|
| Status |
Current
|
| Supersedes |
| SAE AS 18280/2 : 2006 | SLEEVE, INTERNALLY OR EXTERNALLY SWAGED OR WELDED, 24 DEGREE CONE FLARELESS FITTING, 3000 PSI |
| SAE AS 5902 : 2015 | INSTALLATION OF EXTERNALLY SWAGED FITTINGS |
| SAE ARP 994 : 2016 | DESIGN OF TUBING INSTALLATIONS FOR AEROSPACE HYDRAULIC SYSTEMS |
| SAE ARP994C:2023 | Design of Tubing Installations for Aerospace Hydraulic Systems |
| SAE AS 5010 : 2015 | FITTING, TEE, EXTERNAL SWAGE, HYDRAULIC |
| MIL-PRF-6083 Revision G:2013 | HYDRAULIC FLUID, PETROLEUM BASE, FOR PRESERVATION AND OPERATION |
| SAE AMS 5569B : 2011 | STEEL, CORROSION AND HEAT RESISTANT, SEAMLESS AND WELDED HYDRAULIC TUBING, 19CR - 9.5NI - 0.03C MAX, COLD DRAWN, 1/8 HARD TEMPER |
| SAE AS 4234 : 2015 | FITTING, ADAPTER, BEAM SEAL, SWIVEL NUT, EXTERNAL SWAGE TUBE END, HYDRAULIC, 3000 PSI |
| SAE AS 4219 : 2015 | FITTING, ELBOW, 45 DEGREES, BEAM SEAL, BULKHEAD, EXTERNAL SWAGE TUBE END, HYDRAULIC, 3000 PSI |
| SAE AS 603 : 2015 | IMPULSE TESTING OF HYDRAULIC HOSE, TUBING, AND FITTING ASSEMBLIES |
| MIL-PRF-5606 Revision H:2002 | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT, MISSILE, AND ORDNANCE |
| SAE AMS 5656F : 2015 | STEEL, CORROSION RESISTANT, BARS, WIRE, FORGINGS, EXTRUSIONS, AND RINGS, 9.0MN - 20CR - 6.5NI - 0.27N, SOLUTION HEAT TREATED |
| SAE AMS 5561 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, WELDED AND DRAWN OR SEAMLESS AND DRAWN TUBING, 9.0MN - 20CR - 6.5NI - 0.28N, HIGH-PRESSURE HYDRAULIC |
| MIL-HDBK-831 Revision A:2013 | PREPARATION OF TEST REPORTS |
| SAE ARP1185B | FLEXURE TESTING OF HYDRAULIC TUBING JOINTS AND FITTINGS |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AS 4226 : 2015 | FITTING, ELBOW, 90 DEGREES, BEAM SEAL, BULKHEAD, EXTERNAL SWAGE TUBE END, HYDRAULIC, 3000 PSI |
| MIL-PRF-87257 Revision C:2017 | HYDRAULIC FLUID, FIRE RESISTANT, LOW TEMPERATURE, SYNTHETIC HYDROCARBON BASE, AIRCRAFT AND MISSILE |
| SAE AS 7003 : 2008 | NADCAP PROGRAM REQUIREMENTS |
| MIL-DTL-5541 Revision F:2006 | Chemical Conversion Coatings on Aluminum and Aluminum Alloys |
| SAE AS 5009 : 2015 | FITTING, ELBOW, 90 DEGREES, EXTERNAL SWAGE, HYDRAULIC |
| SAE AS 5902 : 2015 | INSTALLATION OF EXTERNALLY SWAGED FITTINGS |
| SAE AS 2001 : 1999 | AEROSPACE FLUID SYSTEMS AND COMPONENTS - PRESSURE AND TEMPERATURE CLASSIFICATIONS |
| SAE AS 6473 : 2016 | FITTING, ELBOW, 90 DEGREES, EXTERNAL SWAGE TO FLARELESS, HYDRAULIC |
| SAE AS 5266 : 2015 | FITTING, ADAPTER, STRAIGHT, FLARED, EXTERNAL SWAGE, HYDRAULIC |
| SAE AS 5267 : 2015 | FITTING, ADAPTER, STRAIGHT, FLARELESS, EXTERNAL SWAGE, HYDRAULIC |
| SAE AMS 4945 : 2014 | TITANIUM ALLOY TUBING, SEAMLESS, HYDRAULIC 3AL - 2.5V, CONTROLLED CONTRACTILE STRAIN RATIO COLD WORKED, STRESS RELIEVED |
| SAE AS 6471 : 2017 | FITTING ASSEMBLY, TEE, FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN, EXTERNAL SWAGE ON BRANCH, HYDRAULIC |
| SAE AMS 4921 : 2016 | TITANIUM BARS, WIRE, FORGINGS, AND RINGS COMMERCIALLY PURE, 70 KSI (483 MPA) YIELD STRENGTH |
| SAE AS1376D | ALTERNATE DIMENSIONS, CENTER BODY SECTION, SHAPE FLUID FITTING, DESIGN STANDARD |
| SAE AMS H 81200 : 2014 | HEAT TREATMENT OF TITANIUM AND TITANIUM ALLOYS |
| SAE AMS4117K | ALUMINUM ALLOY, ROLLED OR COLD FINISHED BARS, RODS, AND WIRE AND FLASH WELDED RINGS, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061; -T6, -T651) |
| SAE AMS4127J | ALUMINUM ALLOY, FORGINGS AND ROLLED OR FORGED RINGS, (6061-T6) SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AS 4215 : 2015 | FITTING, ADAPTER, BEAM SEAL, EXTERNAL THREAD, EXTERNAL SWAGE TUBE END, HYDRAULIC, 3000 PSI |
| SAE AS 1241 : 2016 | FIRE RESISTANT PHOSPHATE ESTER HYDRAULIC FLUID FOR AIRCRAFT |
| SAE AS 5011 : 2015 | FITTING, CROSS, EXTERNAL SWAGE, HYDRAULIC |
| SAE AMS 2700E : 2011 | PASSIVATION OF CORROSION RESISTANT STEELS |
| MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
| SAE AS 5014 : 2015 | FITTING, SLEEVE, STRAIGHT, FLARELESS, EXTERNAL SWAGE, HYDRAULIC |
| SAE AS 4217 : 2015 | FITTING, ADAPTER, BEAM SEAL, BULKHEAD, EXTERNAL SWAGE TUBE END, HYDRAULIC, 3000 PSI |
| SAE AMS4083L | ALUMINUM ALLOY TUBING, HYDRAULIC, SEAMLESS, DRAWN, ROUND, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AS 6478 : 2016 | FITTING, ADAPTER, BULKHEAD, EXTERNAL SWAGE TO MALE FLARELESS, HYDRAULIC |
| ASTM E 8 : 2004 | Standard Test Methods for Tension Testing of Metallic Materials |
| SAE AS 5012 : 2015 | FITTING, SLEEVE, STRAIGHT, FLARED, EXTERNAL SWAGE, HYDRAULIC |
| SAE AS 4225 : 2015 | FITTING, ELBOW, 90 DEGREES, BEAM SEAL, EXTERNAL THREAD, EXTERNAL SWAGE TUBE END, HYDRAULIC, 3000 PSI |
| SAE ARP 4784 : 2013 | DEFINITIONS AND LIMITS, METAL MATERIAL DEFECTS AND SURFACE AND EDGE FEATURES, FLUID COUPLINGS, FITTINGS AND HOSE ENDS |
| SAE AS 5008 : 2015 | FITTING, UNION, EXTERNAL SWAGE, HYDRAULIC |
| SAE AS 7113 : 1997 | NATIONAL AEROSPACE AND DEFENSE CONTACTORS ACCREDITATION PROGRAM REQUIREMENTS FOR FASTENER MANUFACTURING |
| SAE AS 478 : 2015 | IDENTIFICATION MARKING METHODS |
| FED-STD-595 Revision C:2008 | COLORS USED IN GOVERNMENT PROCUREMENT |
| SAE AS 2094 : 2011(S2018) | Test Methods for Tube-Fitting Assemblies(STABILIZED Jul 2018) |
| SAE ARP 9013 : 2005 | STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS |
| SAE AS 4218 : 2015 | FITTING, ELBOW, 45 DEGREES, BEAM SEAL, EXTERNAL THREAD, EXTERNAL SWAGE TUBE END, HYDRAULIC, 3000 PSI |
| SAE AS 5013 : 2015 | FITTING, ADAPTER, STRAIGHT FLARELESS, EXTERNAL SWAGE, HYDRAULIC |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.