SAE J533_201702
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Flares for Tubing
Hardcopy , PDF
29-05-2020
English
08-02-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCES
3. GENERAL SPECIFICATIONS
4. PERFORMANCE REQUIREMENT
5. NOTES
Describes specifications and performance requirements for 37 degrees and 45 degrees single and double flares for tube ends intended for use with SAE J512, SAE J513, SAE J514, and ISO 8434-2 connectors.
| DocumentType |
Standard
|
| Pages |
10
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This SAE Standard covers specifications and performance requirements for 37° and 45° single and double flares for tube ends intended for use with SAE J512, SAE J513, SAE J514, and ISO 8434-2 connectors. The flares described in this document are intended for use with SAE metallic tube materials. Considerations such as the effects of wall thickness selection for specific working pressures, identifying appropriate length of thread engagements for specific applications with mating connectors and other associated criteria, shall be the responsibility of the user. For applicable nominal reference working pressures for hydraulic tubing, see SAE J1065 and ISO 10763.In an effort to standardize within a global marketplace and ensuring that companies can remain competitive in an international market, it is the intent of this document to promote the use of metric tube and connector sizes which will:lead to one global system;guide users to a preferred system;reduce complexity;eliminate inventory duplications.
| ANSI B93.11M : 1981 | SEAMLESS LOW CARBON STEEL HYDRAULIC LINE TUBING, |
| ASTM A 254/A254M : 2012 : REDLINE | Standard Specification for Copper-Brazed Steel Tubing |
| SAE J2593_201502 | Information Report for the Installation of Fluid Conductors and Connectors |
| NFPA 1192 : 2018 | RECREATIONAL VEHICLES |
| NFPA 54 : 2018 | NATIONAL FUEL GAS CODE |
| ANSI Z223.1 : 2018 | NATIONAL FUEL GAS CODE |
| SAE J1650_201112 | Seamless Copper-Nickel 90-10 Tubing |
| ASTM A 254 : 1997 : R2007 | Standard Specification for Copper-Brazed Steel Tubing |
| SAE J2551/2_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 2: General Specifications and Performance Requirements |
| SAE J514_201201 | Hydraulic Tube Fittings |
| SAE J524_201607 | Seamless Low-Carbon Steel Tubing Annealed for Bending and Flaring |
| NFPA 501C : 1996 | RECREATIONAL VEHICLES |
| ASTM A 254 : 1997 : R2002 | Standard Specification for Copper-Brazed Steel Tubing |
| SAE J2467_201506 | Welded and Cold-Drawn, SAE 1021 Carbon Steel Tubing Normalized for Bending and Flaring |
| SAE J1290_201207 | Automotive Hydraulic Brake System - Metric Tube Connections |
| ASTM B 469 : 1994 | Standard Specification for Seamless Copper-Alloy Tubes for Pressure Applications (Withdrawn 2000) |
| SAE J527_201710 | Brazed Double Wall Low-Carbon Steel Tubing |
| SAE J525_201609 | Welded and Cold Drawn Low-Carbon Steel Tubing Annealed for Bending and Flaring |
| SAE J2435_201508 | Welded Flash Controlled, SAE 1021 Carbon Steel Tubing, Normalized for Cold Forming, Welding and Brazing |
| SAE J2467_202005 | Welded and Cold-Drawn, SAE 1021 Carbon Steel Tubing Normalized for Bending, Single Flaring, Cold Forming, Welding, and Brazing |
| I.S. 808:2002 | SPECIFICATION FOR CNG FUELLED VEHICLES |
| ASTM A 254 : 1997 | Standard Specification for Copper-Brazed Steel Tubing |
| SAE J356_201312 | Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading |
| SAE J1065_201605 | Nominal Reference Working Pressures for Steel Hydraulic Tubing |
| SAE J2551_201309 | Recommended Practices for Fluid Conductor Carbon and Alloy Steel Tubing Applications |
| SAE J2551/1_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 1: Design and Fabrication |
| SAE J2551/3_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications - Part 3: Procurement |
| SAE J1677_201612 | Tests and Procedures for Carbon Steel and High Strength Low Alloy Steel Tubing |
| SAE J512_201705 | Automotive Tube Fittings |
| SAE J513_199901 | Refrigeration Tube Fittings—General Specifications |
| SAE J2613_201710 | Welded Flash Controlled, High Strength (500 MPa Tensile Strength) Hydraulic Tubing, for Bending, Double Flaring, Cold Forming, Welding, and Brazing |
| SAE J2614_201801 | Welded and Cold-Drawn, High Strength (500 MPa Tensile Strength) Hydraulic Tubing, for Bending, Flaring, Cold Forming, Welding and Brazing |
| SAE AS 4775 : 2017 | AIRCRAFT MAINTENANCE JACKS - GENERAL REQUIREMENTS |
| SAE J526_201611 | Welded Low-Carbon Steel Tubing Suitable for Bending, Flaring, Beading, Forming and Brazing |
| SAE ARP1247E | Aircraft Ground Support Equipment – General Requirements |
| NFPA T2.24.2 : 2007 | HYDRAULIC FLUID POWER SYSTEMS - METHODS FOR PREVENTING EXTERNAL LEAKAGE |
| NFPA T2.24.2 : 2007 : R2012 | HYDRAULIC FLUID POWER SYSTEMS - METHODS FOR PREVENTING EXTERNAL LEAKAGE |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| ASME Y14.5 : 2009 | DIMENSIONING AND TOLERANCING |
| ISO 4399:1995 | Fluid power systems and components Connectors and associated components Nominal pressures |
| SAE J2879_201107 | Automotive Hydraulic Brake Tube Joints |
| ISO 10583:1993 | Aerospace fluid systems — Test methods for tube/fitting assemblies |
| ISO 6605:2017 | Hydraulic fluid power — Test methods for hoses and hose assemblies |
| ISO 4397:2011 | Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes |
| SAE J1290_201207 | Automotive Hydraulic Brake System - Metric Tube Connections |
| SAE J2551/1_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 1: Design and Fabrication |
| SAE J513_199901 | Refrigeration Tube Fittings—General Specifications |
| SAE J1273_201409 | Recommended Practices for Hydraulic Hose Assemblies |
| SAE J1065_201605 | Nominal Reference Working Pressures for Steel Hydraulic Tubing |
| SAE J356_201312 | Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading |
| ISO 8434-2:2007 | Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors |
| SAE J2614_200909 | Welded and Cold-Drawn, High Strength (500 MPa Tensile Strength) Low Alloy Steel Hydraulic Tubing, Sub-Critically Annealed for Bending and Flaring |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| SAE J2435_201508 | Welded Flash Controlled, SAE 1021 Carbon Steel Tubing, Normalized for Cold Forming, Welding and Brazing |
| SAE J514_201201 | Hydraulic Tube Fittings |
| SAE J526_201611 | Welded Low-Carbon Steel Tubing Suitable for Bending, Flaring, Beading, Forming and Brazing |
| SAE J527_201306 | Brazed Double Wall Low-Carbon Steel Tubing |
| SAE J525_201609 | Welded and Cold Drawn Low-Carbon Steel Tubing Annealed for Bending and Flaring |
| SAE J1677_201612 | Tests and Procedures for Carbon Steel and High Strength Low Alloy Steel Tubing |
| SAE J524_201607 | Seamless Low-Carbon Steel Tubing Annealed for Bending and Flaring |
| ISO 10763:1994 | Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures |
| SAE J2467_201506 | Welded and Cold-Drawn, SAE 1021 Carbon Steel Tubing Normalized for Bending and Flaring |
| SAE J1176_201206 | External Leakage Classifications for Hydraulic Systems |
| SAE TSB003_199905 | Rules for SAE Use of SI (Metric) Units |
| SAE J2551/2_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 2: General Specifications and Performance Requirements |
| ISO 2944:2000 | Fluid power systems and components — Nominal pressures |
| SAE J2551/3_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications - Part 3: Procurement |
| ISO 13486-1:1999 | Road vehicles Hydraulic braking systems Part 1: Double-flare pipes, tapped holes, male fittings and tube seats |
| SAE J512_199704 | AUTOMOTIVE TUBE FITTINGS |
| SAE J2613_200909 | Welded Flash Controlled, High Strength (500 MPa Tensile Strength) Low Alloy Steel Hydraulic Tubing, Sub-Critically Annealed for Bending, Double Flaring, and Bending |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.