SN EN 60107-7 : 1997

1 General
    1.1 Scope and object
    1.2 Normative references
    1.3 Definitions
    1.4 Types of displays
2 General notes on measurements
    2.1 General
          2.1.1 Operation conditions
          2.1.2 Presentation of results
          2.1.3 Environmental conditions
          2.1.4 Precautions during measurement
          2.1.5 Power supply
          2.1.6 Stabilization period
          2.1.7 Test room
    2.2 Input signals
          2.2.1 Video signals
    2.3 Test signals
          2.3.1 Video test signals (general remarks)
          2.3.2 Audio test signals
    2.4 Test instruments
          2.4.1 Video test signal generator
          2.4.2 Audio test signal generator
          2.4.3 Oscilloscope
          2.4.4 Luminance meter and colorimeter
          2.4.5 Other optical measuring instruments
          2.4.6 Measurement setup
    2.5 Standard measuring conditions
          2.5.1 Standard input signal levels
          2.5.2 Standard output signal levels
          2.5.3 Standard display settings
          2.5.4 General measurement procedure
3 Tests under general operating conditions
    3.1 Electrical and mechanical performance
          3.1.1 Introduction
          3.1.2 Methods of measurement
    3.2 Power consumption
          3.2.1 Method of measurement
4 Characteristics of displayed pictures
    4.1 General properties of the picture
          4.1.1 General
          4.1.2 Geometrical distortion
          4.1.3 Over- and under-scanning and centring
          4.1.4 Luminance and contrast
          4.1.5 Uniformity of luminance
          4.1.6 Uniformity of chromaticity
          4.1.7 Convergence and registration errors
          4.1.8 White balance
          4.1.9 Resolution
          4.1.10 Colour fidelity
          4.1.11 Picture breathing
          4.1.12 Local picture distortion
          4.1.13 Sound-to-picture interference
          4.1.14 Other characteristics of the picture
    4.2 Synchronizing quality
          4.2.1 Synchronizing range
          4.2.2 Pulling on whites
          4.2.3 Quality of interface
    4.3 Characteristics inherent in projection type
          displays
          4.3.1 General
          4.3.2 Viewing angle and dependence of luminance
                  uniformity on the angle
          4.3.3 Dependence of chromaticity on viewing
                  angle
          4.3.4 Screen gain and luminous flux index
                  of a projector
    4.4 Characteristics inherent in LCD displays
          4.4.1 General
          4.4.2 Viewing angle and dependence of
                  luminance uniformity on the angle
          4.4.3 Dependence of chromaticity on viewing
                  angle
          4.4.4 Variation of luminance with time
5 Characteristics of video channels
    5.1 Characteristics of the luminance channel
          5.1.1 General
          5.1.2 Amplitude response to video frequency
          5.1.3 Linear waveform response
          5.1.4 Line time non-linearity
          5.1.5 Black level stability
    5.2 Characteristics of the colour difference channel
          5.2.1 General
          5.2.2 Matrix error
          5.2.3 Y/C timing
          5.2.4 Other characteristics
Tables
Figures
Annex A Bibliography
Annex ZA (normative) Normative references to international
          publications with their corresponding
          European publications

Concerned with standard conditions and management methods on high definition television displays. May be used as an integral part of an HDTV receiver for direct off-air reception, reception via cabled networks or as a monitor for pre-recorded video, home movies and games, among other uses. Determines the performance and allows the comparing of equipment by listing of the characteristics useful for specifications and by defining uniform measurement methods for these characteristics. Does not define performance or general safety methods.