UNI EN 14382 : 2009
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY DEVICES FOR GAS PRESSURE REGULATING STATIONS AND INSTALLATIONS - GAS SAFETY SHUT-OFF DEVICES FOR INLET PRESSURES UP TO 100 BAR
Superseded date
09-08-2022
Superseded by
Published date
01-01-2009
Sorry this product is not available in your region.
Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Construction requirements
5 Functional requirements
6 Testing
7 Test and verification methods
8 Documentation
9 Marking
Annex A (informative) Ice formation
Annex B (informative) Compliance evaluation
Annex C (informative) Pressure drop and flow coefficient
Annex D (informative) Alternative test method for
verification of the strength of the trip mechanism,
valve seat and closing member
Annex E (informative) Sizing equation
Annex F (informative) Inspection certificate
Annex G (informative) Order specification
Annex H (informative) Acceptance test
Annex I (informative) Seat leakage (alternative requirement)
Annex J (normative) Materials
Annex K (informative) Suitability of safety shut-off device
for damp operating conditions
Annex L (informative) Glossary
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 97/23/EC
Bibliography
Describes constructional, functional, testing and marking requirements, sizing and documentation of gas safety shut-off devices used in the pressure regulating stations.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 14382 : AUG 2009 | Identical |
| BS EN 14382 : 2005 | Identical |
| DIN EN 14382:2016-05 (Draft) | Identical |
| NEN EN 14382 : 2005 + A1/C1 2009 | Identical |
| NF EN 14382 : 2005 + A1 2009 | Identical |
| I.S. EN 14382:2005 | Identical |
| UNE-EN 14382:2005 | Identical |
| NBN EN 14382 : 2005 + A1 2009 | Identical |
| SN EN 14382 : 2009 CORR 2009 | Identical |
| UNI 9167 : 2009 | INITIAL PRESSURE AND REDUCTION PLANTS FOR NATURAL GAS - DESIGN, CONSTRUCTION AND TESTING |
| UNI 10619-2 : 2014 | GAS PRESSURE CONTROL SYSTEMS AND/OR GAS MEASUREMENT INSTALLATIONS FOR INLET MAX PRESSURE UP TO 12 BAR FOR INDUSTRIAL AND DOMESTIC USE - PART 2: DESIGN, CONSTRUCTION AND TESTING - EQUIPMENT FOR GAS CONTROL |
| UNI 10619-1 : 2014 | GAS PRESSURE CONTROL SYSTEMS AND/OR GAS MEASUREMENT INSTALLATIONS FOR INLET MAX PRESSURE UP TO 12 BAR FOR INDUSTRIAL AND DOMESTIC USE - PART 1: DESIGN, CONSTRUCTION AND TESTING - GENERAL |
| EN 12732:2013+A1:2014 | Gas infrastructure - Welding steel pipework - Functional requirements |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 9606-4:1999 | Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys |
| ISO/IEC 17050-1:2004 | Conformity assessment Supplier's declaration of conformity Part 1: General requirements |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 1349:2009 | Industrial process control valves |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| IEC 60534-3-1:2000 | Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves |
| EN 1759-4:2003 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 4: Aluminium alloy flanges |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN ISO 2409:2013 | Paints and varnishes - Cross-cut test (ISO 2409:2013) |
| EN 12516-1:2014 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| EN ISO 9606-4:1999 | Approval testing of welders - Fusion welding - Part 4: Nickel and nickel alloys (ISO 9606-4:1999) |
| EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN 13906-2:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN 1092-4:2002 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| ISO 5752:1982 | Metal valves for use in flanged pipe systems Face-to-face and centre-to-face dimensions |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 148:1983 | Steel — Charpy impact test (V-notch) |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| ISO 175:2010 | Plastics Methods of test for the determination of the effects of immersion in liquid chemicals |
| IEC 60534-3-2:2001 | Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves |
| EN 334:2005+A1:2009 | Gas pressure regulators for inlet pressures up to 100 bar |
| EN 60534-3-2:2001 | Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves |
| ISO 1518:1992 | Paints and varnishes Scratch test |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 45020:2006 | Standardization and related activities - General vocabulary (ISO/IEC Guide 2:2004) |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| ASME B16.34 : 2017 | VALVES - FLANGED, THREADED, AND WELDING END |
| EN 60534-3-1:2000/corrigendum:2000 | INDUSTRIAL-PROCESS CONTROL VALVES - PART 3-1: DIMENSIONS - FACE-TO-FACE DIMENSIONS FOR FLANGED, TWO-WAY, GLOBE-TYPE, STRAIGHT PATTERN AND CENTRE-TO-FACE DIMENSIONS FOR FLANGED, TWO-WAY, GLOBE-TYPE, ANGLE PATTERN CONTROL VALVES |
| MSS SP 55 : 2011 | QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES |
| ISO/IEC Guide 2:2004 | Standardization and related activities — General vocabulary |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO/IEC Guide 65:1996 | General requirements for bodies operating product certification systems |
| EN ISO/IEC 17050-1:2010 | Conformity assessment - Supplier's declaration of conformity - Part 1: General requirements (ISO/IEC 17050-1:2004, corrected version 2007-06-15) |
| EN ISO 1518:2000 | Paints and varnishes - Scratch test (ISO 1518:1992) |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| EN 45020 : 2006 | STANDARDIZATION AND RELATED ACTIVITIES - GENERAL VOCABULARY |
| EN 12516-2:2014 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| IEC 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| EN ISO 9606-3:1999 | Approval testing of welders - Fusion welding - Part 3: Copper and copper alloys (ISO 9606-3:1999) |
| IEC 60534-3:1976 | Industrial-process control valves. Part 3: Dimensions - Section One: Face-to-face dimensions for flanged, two-way, globe-type control valves |
| EN ISO 175:2010 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 9606-3:1999 | Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN 12186:2014 | Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.