Skip to content
Please enter a keyword to search

  • 13/30248785 DC : 0

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    BS EN 61800-2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 2: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE FREQUENCY A.C. POWER DRIVE SYSTEMS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-10-2015

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    1 Introduction
    2 Scope
    3 Normative references
    4 Terms and definitions
    5 Ratings and specifications for installation, commissioning
      and operation
    6 Test
    7 Information & marking requirements

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PEL/22
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61800-3:2017 Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods
    IEC 60079-1:2014 RLV Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
    IEC 60038:2009 IEC standard voltages
    IEC 61800-4:2002 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
    IEC 61158-2:2014 Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition
    IEC 61800-7-301 : 2.0 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 7-301: GENERIC INTERFACE AND USE OF PROFILES FOR POWER DRIVE SYSTEMS - MAPPING OF PROFILE TYPE 1 TO NETWORK TECHNOLOGIES
    IEC 60068-2-68:1994 Environmental testing - Part 2-68: Tests - Test L: Dust and sand
    IEC 60034-9:2003+AMD1:2007 CSV Rotating electrical machines - Part 9: Noise limits
    IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
    IEC 61800-7-303:2015 Adjustable speed electrical power drive systems - Part 7-303: Generic interface and use of profiles for power drive systems - Mapping of profile type 3 to network technologies
    IEC TS 62578:2015 Power electronics systems and equipment - Operation conditions and characteristics of active infeed converter (AIC) applications including design recommendations for their emission values below 150 kHz
    IEC 61800-7-1:2015 Adjustable speed electrical power drive systems - Part 7-1: Generic interface and use of profiles for power drive systems - Interface definition
    IEC 61800-7-204:2015 Adjustable speed electrical power drive systems - Part 7-204: Generic interface and use of profiles for power drive systems - Profile type 4 specification
    IEC 61800-7-302:2015 Adjustable speed electrical power drive systems - Part 7-302: Generic interface and use of profiles for power drive systems - Mapping of profile type 2 to network technologies
    IEC 61800-7-304:2015 Adjustable speed electrical power drive systems - Part 7-304: Generic interface and use of profiles for power drive systems - Mapping of profile type 4 to network technologies
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    IEC 61800-7-201 : 2.0 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 7-201: GENERIC INTERFACE AND USE OF PROFILES FOR POWER DRIVE SYSTEMS - PROFILE TYPE 1 SPECIFICATION
    IEC TS 61800-8:2010 Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
    IEC 60079-11:2011 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
    IEC 60721-2-6:1990 Classification of environmental conditions. Part 2: Environmental conditions appearing in nature. Earthquake vibration and shock
    IEC 60146-1-1:2009 Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements
    IEC 60027-3:2002 Letter symbols to be used in electrical technology - Part 3: Logarithmic and related quantities, and their units
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60721-3-2:1997 Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 2: Transportation
    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
    IEC 60034-1:2017 Rotating electrical machines - Part 1: Rating and performance
    IEC 61800-7-203:2015 Adjustable speed electrical power drive systems - Part 7-203: Generic interface and use of profiles for power drive systems - Profile type 3 specification
    IEC 61378-3:2015 Converter transformers - Part 3: Application guide
    IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
    IEC 60079-31:2013 Explosive atmospheres - Part 31: Equipment dust ignition protection by enclosure "t"
    IEC TR 61800-6:2003 Adjustable speed electrical power drive systems - Part 6: Guide for determination of types of load duty and corresponding current ratings
    EN 50495:2010 Safety devices required for the safe functioning of equipment with respect to explosion risks
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    IEC 60068-2-52:2017 Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution)
    IEC 61378-1:2011 Converter transformers - Part 1: Transformers for industrial applications
    IEC 61800-7-202:2015 Adjustable speed electrical power drive systems - Part 7-202: Generic interface and use of profiles for power drive systems - Profile type 2 specification
    IEC 61800-5-2:2016 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
    IEC 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
    IEC 60079-26:2014 RLV Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga
    IEC 60721-3-1:1997 Classification of environmental conditions - Part 3 Classification of groups of environmental parameters and their severities - Section 1: Storage
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective