09/30186728 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 62040-3 - UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 3: METHOD OF SPECIFYING THE PERFORMANCE AND TEST REQUIREMENTS
Hardcopy , PDF
31-05-2012
English
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
3.1 Systems and components
3.2 Performance of systems and components
3.3 Specified values - General
3.4 Input values
3.5 Output values
4 Environmental conditions
4.1 Introduction
4.2 Normal conditions
4.3 Unusual conditions
5 Electrical conditions, performance and declared
values
5.1 General
5.2 UPS input specification
5.3 UPS output specification
5.4 Stored energy specification
5.5 UPS switch specification
5.6 Communication circuits
6 UPS tests
6.1 Summary
6.2 Routine test procedure
6.3 Site test procedure
6.4 Type test procedure (electrical)
6.5 Type test procedure (environmental)
6.6 UPS functional unit tests (where not tested
as a complete UPS)
Annex A (informative) - Uninterruptible Power System
(UPS) configurations
A.1 Single UPS
A.2 Parallel UPS
A.3 Redundant UPS
Annex B (informative) - Topologies - Uninterruptible
Power System (UPS)
B.1 Double conversion topology
B.2 Double conversion topology with bypass
B.3 Line-interactive topology
B.4 Line-interactive topology with bypass
B.5 Passive stand-by topology
Annex C (informative) - UPS switch applications
C.1 Interrupters
C.2 Transfer switches, bypass transfer switches
C.3 Isolation switches
C.4 Maintenance bypass switches
C.5 Tie switches
C.6 Multiple function switches
Annex D (informative) - Purchaser specification guidelines
D.1 Load to be supplied by the UPS
D.3 Stored energy device (battery - where applicable)
D.4 Physical and environmental requirements
D.5 Electromagnetic compatibility
D.6 UPS Technical data sheet - Manufacturer's
declaration
Annex E (normative) - Reference non-linear load
Annex F (informative) - notes on backfeed protection
Annex G (normative) - Input mains failure - test method
Test G.1 - High impedance mains failure
Test G.2 - Low impedance mains failure
Annex H (informative) - Dynamic output performance -
Measurement techniques
H.1 Assessment method
H.2 Graphical validating methods
Annex I (informative) - Energy Efficiency of Uninterruptible
Power Systems above 10kVA
Annex J (informative) - Functional Safety of UPS
Annex K (informative) - Environmental information on UPS
Annex L (informative) - Bibliography
BS EN 62040-3
| Committee |
PEL/22
|
| DocumentType |
Draft
|
| Pages |
105
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60146-1-3:1991 | Semiconductor convertors - General requirements and line commutated convertors - Part 1-3: Transformers and reactors |
| IEC 60478-1:1974 | Stabilized power supplies, d.c. output. Part 1: Terms and definitions |
| IEC 60146-1-1:2009 | Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60478-2:1986 | Stabilized power supplies, d.c. output. Part 2: Rating and performance |
| IEC 60146-2:1999 | Semiconductor converters - Part 2: Self-commutated semiconductor converters including direct d.c. converters |
| IEC TS 61000-3-4:1998 | Electromagnetic compatibility (EMC) - Part 3-4: Limits - Limitation of emission of harmonic currents in low-voltage power supply systems for equipment with rated current greater than 16 A |
| IEC 61000-2-2:2002+AMD1:2017 CSV | Electromagnetic compatibility (EMC) - Part 2-2: Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems |
| IEC 60478-4:1976 | Stabilized power supplies, d.c. output. Part 4: Tests other than radio-frequency interference |
| IEC 60146-3:1977 | Semiconductor convertors. Part 3: Semiconductor direct d.c. convertors (d.c. chopper convertors) |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
| IEC 60478-3:1989 | Stabilized power supplies, d.c. output. Part 3: Reference levels and measurement of conducted electromagnetic interference (EMI) |
| IEC 60686:1980 | Stabilized power supplies, a.c. output |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.