• IEC TS 61000-3-4:1998

    Current The latest, up-to-date edition.

    Electromagnetic compatibility (EMC) - Part 3-4: Limits - Limitation of emission of harmonic currents in low-voltage power supply systems for equipment with rated current greater than 16 A

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  English - French, Spanish, Castilian

    Published date:  30-10-1998

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Abstract - (Show below) - (Hide below)

    The recommendations of this technical report are applicable to electrical and electronic equipment with a rated input current exceeding 16 A per phase and intended to be connected to public low-voltage a.c. distribution systems of the following types: - nominal voltage up to 240 V, single-phase, two or three wires; - nominal voltage up to 600 V, three-phase, three or four wires; - nominal frequency 50 Hz or 60 Hz. These recommendations specify the information required to enable a supply authority to assess equipment regarding harmonic disturbance and to decide wether or not the equipment is acceptable for connection with regard to the harmonic distortion aspect. This document is not to be regarded as an International Standard.

    General Product Information - (Show below) - (Hide below)

    Committee TC 77/SC 77A
    Development Note Stability Date: 2017. (10/2012)
    Document Type Technical Specification
    Publisher International Electrotechnical Committee
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN 60974-10 : 2014 ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS
    IEC TR 61000-3-6:2008 Electromagnetic compatibility (EMC) - Part 3-6: Limits - Assessment of emission limits for the connection of distorting installations to MV, HV and EHV power systems
    03/111744 DC : DRAFT JULY 2003
    NF EN 61000-4-1 : 2007
    CLC/TS 50217 : 2005 GUIDE FOR IN SITU MEASUREMENTS - IN SITU MEASUREMENT OF DISTURBANCE EMISSION
    BS EN 62282-3-1 : 2007 FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    BS ISO 16110-1 : 2007 HYDROGEN GENERATORS USING FUEL PROCESSING TECHNOLOGIES - PART 1: SAFETY
    ISO 22199:2009 Electromagnetic compatibility Product family standard for lifts, escalators and moving walks Emission
    UNE-EN 62282-3-1:2011 Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety
    08/30185866 DC : DRAFT JULY 2008 BS EN 61000-3-15 - ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-15: LIMITS - ASSESSMENT OF LOW FREQUENCY ELECTROMAGNETIC IMMUNITY AND EMISSION REQUIREMENTS FOR DISPERSED GENERATION SYSTEMS IN LV NETWORK
    12/30250727 DC : 0 BS EN ISO 13628-6 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 6: SUBSEA PRODUCTION CONTROL SYSTEMS
    BS PD IEC TR 61000-3-6 : 2008 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-6: LIMITS - ASSESSMENT OF EMISSION LIMITS FOR THE CONNECTION OF DISTORTING INSTALLATIONS TO MV, HV AND EHV POWER SYSTEMS
    I.S. EN 61000-4-1:2007 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES - OVERVIEW OF IEC 61000-4 SERIES
    03/107918 DC : DRAFT MAY 2003 IEC 61000-4-1 ED.2 - ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES - OVERVIEW OF IEC 61000-4 SERIES
    BS EN 61000-4-7 : 2002 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO
    08/30183041 DC : DRAFT MAY 2008 BS EN 61000-3-12 - ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW VOLTAGE SYSTEMS WITH INPUT CURRENT $OG 16 A AND <= 75 A PER PHASE
    IEC TR 61000-2-5 REDLINE : 3ED 2017 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 2-5: ENVIRONMENT - DESCRIPTION AND CLASSIFICATION OF ELECTROMAGNETIC ENVIRONMENTS
    BS EN 62135-2:2015 (published 2015-05) Resistance welding equipment Electromagnetic compatibility (EMC) requirements
    10/30238615 DC : DRAFT NOV 2010 BS EN 62282-3-100 - FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    09/30186728 DC : 0 BS EN 62040-3 - UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 3: METHOD OF SPECIFYING THE PERFORMANCE AND TEST REQUIREMENTS
    07/30164322 DC : 0 BS EN 61000-3-6 ED.2 - ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-6: ASSESSMENT OF HARMONIC EMISSION LIMITS FOR THE CONNECTION OF DISTORTING INSTALLATIONS TO MV, HV AND EHV POWER SYSTEMS
    BS EN 61000-3-12 : 2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE
    16/30354071 DC : 0 BS EN 62282-3-100 - FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    I.S. EN 62282-3-1:2007 FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    09/30214220 DC : 0 BS IEC TR 61000-2-5 ED - ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 2-5: ENVIRONMENT - CLASSIFICATION OF ELECTROMAGNETIC ENVIRONMENTS
    14/30269850 DC : 0 BS EN 62135-2 - ED 2.0 - RESISTANCE WELDING EQUIPMENT - PART 2: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS
    06/30156472 DC : DRAFT SEP 2006 BS EN 60146-1-1 - SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS
    00/560888 DC : APR 2000 IEC 60601-1-2 EDITION 2 - MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR SAFETY - COLLATERAL STANDARD - ELECTROMAGNETIC COMPATIBILITY - REQUIREMENTS AND TESTS
    PD IEC/TR 61000-3-15:2011 (published 2011-10) Electromagnetic compatibility (EMC) Limits. Assessment of low frequency electromagnetic immunity and emission requirements for dispersed generation systems in LV network
    CEI EN 61000-4-1 : 2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES - OVERVIEW OF IEC 61000-4 SERIES
    CEI EN 62282-3-100 : 2012 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    04/30116077 DC : DRAFT JUL 2004
    BS EN 62282-3-100 : 2012 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    IEC TR 61000-2-5:2017 Electromagnetic compatibility (EMC) - Part 2-5: Environment - Description and classification of electromagnetic environments
    CSA C61000.4.1 : 2009 : R2014 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES - OVERVIEW OF IEC 61000-4 SERIES
    02/204840 DC : DRAFT APR 2002 PREN 50217 - IN SITU MEASUREMENTS OF DISTURBANCE EMISSION
    BS EN 61000-4-1:2007 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES - OVERVIEW OF IEC 61000-4 SERIES
    03/108042 DC : DRAFT MAY 2003 IEC 61000-4-1 - ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES
    04/302050 DC : DRAFT JAN 2004 ISO 13628-6 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 6: SUBSEA PRODUCTION CONTROL SYSTEMS
    PD IEC/TR 61000-1-4:2005 (published 2006-01) Electromagnetic compatibility (EMC) General - Historical rationale for the limitation of power-frequency conducted harmonic current emmissions from equipment, in the frequency range up to 2 kHz
    CSA C61000.3.6 : 2009 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-6: LIMITS - ASSESSMENT OF EMISSION LIMITS FOR THE CONNECTION OF DISTORTING INSTALLATIONS TO MV, HV AND EHV POWER SYSTEMS
    ANSI/CSA FC 1:2014 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    CSA C61000.3.6 : 2009 : R2014 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-6: LIMITS - ASSESSMENT OF EMISSION LIMITS FOR THE CONNECTION OF DISTORTING INSTALLATIONS TO MV, HV AND EHV POWER SYSTEMS
    EN 62040-3:2011 UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 3: METHOD OF SPECIFYING THE PERFORMANCE AND TEST REQUIREMENTS (IEC 62040-3:2011)
    BS EN 60146-1-1 : 2010 SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS
    I.S. EN 61000-3-12:2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE (IEC 61000-3-12:2011 (EQV))
    PD IEC/TR 61000-2-5:2017 (published 2017-02) Electromagnetic compatibility (EMC) Environment. Description and classification of electromagnetic environments
    CSA C61000.4.1:2009 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES - OVERVIEW OF IEC 61000-4 SERIES
    BS EN 62040-3:2011 Uninterruptible power systems (UPS) Method of specifying the performance and test requirements
    IEC TR 61000-1-4:2005 Electromagnetic compatibility (EMC) - Part 1-4: General - Historical rationale for the limitation of power-frequency conducted harmonic current emissions from equipment, in the frequency range up to 2 kHz
    I.S. EN 62282-3-100:2012 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-3-100:2012 (EQV))
    CEI EN 61000-3-12 : 2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE
    BS EN 61800-3 : 2004 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS
    API 17F REDLINE : 2006 SPECIFICATION FOR SUBSEA PRODUCTION CONTROL SYSTEMS
    NF EN 50240 : 2005 ELECTROMAGNETIC COMPATIBILITY (EMC) - PRODUCT STANDARD FOR RESISTANCE WELDING EQUIPMENT
    UNE-EN 61000-3-12:2012 Electromagnetic compatibility (EMC) - Part 3-12: Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16 A and
    I.S. EN 60974-10:2014 ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS
    I.S. CLC/TS 50217:2005 GUIDE FOR IN SITU MEASUREMENTS - IN SITU MEASUREMENT OF DISTURBANCE EMISSION
    IEC TR 61000-3-15:2011 Electromagnetic compatibility (EMC) - Part 3-15: Limits - Assessment of low frequency electromagnetic immunity and emission requirements for dispersed generation systems in LV network
    I.S. EN 61000-3-2:2014 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)
    IEC TR 61000-4-1:2016 Electromagnetic compatibility (EMC) - Part 4-1: Testing and measurement techniques - Overview of IEC 61000-4 series
    BS EN 61000-3-2:2014 (published 2014-09) Electromagnetic compatibility (EMC) Limits. Limits for harmonic current emissions (equipment input current 16 A per phase)
    NF ISO 16110-1 : 2009 HYDROGEN GENERATORS USING FUEL PROCESSING TECHNOLOGIES - PART 1: SAFETY
    CEI EN 60146-1-1 : 2013 SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS
    I.S. EN 50240:2006
    I.S. EN 60146-1-1:2010 SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS
    11/30250199 DC : 0 BS EN 60974-10 - ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS
    00/244020 DC : DRAFT SEP 2000 IEC 61800-3 ED.2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS PRODUCT STANDARD INCLUDING SPECIFIC TEST METHODS
    I.S. EN 12098-4:2005 CONTROLS FOR HEATING SYSTEMS - PART 4: OPTIMUM START-STOP CONTROL EQUIPMENT FOR ELECTRICAL SYSTEMS
    DD CLC/TS 50217 : 2005 GUIDE FOR IN SITU MEASUREMENTS - IN SITU MEASUREMENT OF DISTURBANCE EMISSION
    BS EN 50240 : 2004
    I.S. EN 62135-2:2015 RESISTANCE WELDING EQUIPMENT - PART 2: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS
    I.S. EN 61800-3:2005 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004 (EQV))
    ISO 16110-1:2007 Hydrogen generators using fuel processing technologies Part 1: Safety
    I.S. EN 62040-3:2011 UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 3: METHOD OF SPECIFYING THE PERFORMANCE AND TEST REQUIREMENTS
    EN 61800-3 : 2004 AMD 1 2012 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004/A1:2011)
    IEC TR 61000-2-5:2017 RLV Electromagnetic compatibility (EMC) - Part 2-5: Environment - Description and classification of electromagnetic environments
    IEC 61000-4-1:2006 Electromagnetic compatibility (EMC) - Part 4-1: Testing and measurement techniques - Overview of IEC 61000-4 series
    13/30277685 DC : 0 BS EN 60519-1 - SAFETY IN INSTALLATIONS FOR ELECTROHEATING AND ELECTROMAGNETIC PROCESSING - PART 1: GENERAL REQUIREMENTS
    BS EN 12098-4 : 2005 CONTROLS FOR HEATING SYSTEMS - PART 4: OPTIMUM START-STOP CONTROL EQUIPMENT FOR ELECTRICAL SYSTEMS
    EN 62282-3-100 : 2012 FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-3-100:2012)
    IEC 62282-3-1:2007 Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety
    IEC 61000-3-12:2011 Electromagnetic compatibility (EMC) - Part 3-12: Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current >16 A and ≤ 75 A per phase
    IEC 60974-10:2014+AMD1:2015 CSV Arc welding equipment - Part 10: Electromagnetic compatibility (EMC)requirements
    UNE-ISO 16110-1:2015 Hydrogen generators using fuel processing technologies -- Part 1: Safety
    IEC 62040-3:2011 Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements
    ISO 13628-6:2006 Petroleum and natural gas industries Design and operation of subsea production systems Part 6: Subsea production control systems
    IEC 62282-3-100:2012 Fuel cell technologies - Part 3-100: Stationary fuel cell power systems - Safety
    IEC 62135-2:2015 Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements
    BS EN ISO 13628-6:2006 (published 2006-05) Petroleum and natural gas industries. Design and operation of subsea production systems Subsea production control systems
    DIN EN 12098-4:2005-12 CONTROLS FOR HEATING SYSTEMS - PART 4: OPTIMUM START-STOP CONTROL EQUIPMENT FOR ELECTRICAL SYSTEMS
    EN 12098-4 : 2005 CONTROLS FOR HEATING SYSTEMS - PART 4: OPTIMUM START-STOP CONTROL EQUIPMENT FOR ELECTRICAL SYSTEMS
    EN 62282-3-1 : 2007 FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    EN 61000-3-12:2011 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE (IEC 61000-3-12:2011)
    EN 61000-4-1:2007 Electromagnetic compatibility (EMC) - Part 4-1: Testing and measurement techniques - Overview of IEC 61000-4 series
    EN 60146-1-1:2010 SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS
    EN 62135-2:2015 RESISTANCE WELDING EQUIPMENT - PART 2: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS (IEC 62135-2:2015)
    EN 61000-3-2:2014 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE) (IEC 61000-3-2:2014)
    EN 50240:2004/corrigendum:2005
    EN 60974-10:2014/A1:2015 ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS (IEC 60974-10:2014/A1:2015)
    EN ISO 13628-6 : 2006 PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 6: SUBSEA PRODUCTION CONTROL SYSTEMS

    Standards Referencing This Book - (Show below) - (Hide below)

    SA TR IEC 61000.2.5:2019 Electromagnetic compatibility (EMC) Environment - Description and classification of electromagnetic environments
    IEC TR 61000-2-1:1990 Electromagnetic compatibility (EMC) - Part 2: Environment - Section 1: Description of the environment - Electromagnetic environment for low-frequency conducted disturbances and signalling in public power supply systems
    IEC 61000-2-2:2002+AMD1:2017 CSV Electromagnetic compatibility (EMC) - Part 2-2: Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems
    IEC 61000-4-7:2002+AMD1:2008 CSV Electromagnetic compatibility (EMC) - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto
    IEC 61000-3-2 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective