12/30250146 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 16143-1 - STAINLESS STEELS FOR GENERAL PURPOSES - PART 1: FLAT PRODUCTS
Hardcopy , PDF
English
31-05-2014
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Information to be supplied by the purchaser
6 Classification of grades
7 Requirements
8 Inspection, testing and conformance of products
9 Marking
Annex A (normative) - Guidelines for further treatment
(including heat treatment) in fabrication
Annex B (informative) - Designations of the steels given
in Table 1 and of comparable grades covered in ASTM-,
EN-, JIS- and GB-Standards
Annex C (informative) - Comparison list of abbreviations for
process route/surface finish of flat products given in
Table 3 covered in ASTM- and JIS-Standards
Annex D (informative) - Applicable dimensional standards
Bibliography
BS ISO 16143-1
| Committee |
ISE/105
|
| DocumentType |
Draft
|
| Pages |
45
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 404:2013 | Steel and steel products — General technical delivery requirements |
| ISO 6507-1:2005 | Metallic materials — Vickers hardness test — Part 1: Test method |
| ISO 6929:2013 | Steel products — Vocabulary |
| ISO 6506-1:2014 | Metallic materials — Brinell hardness test — Part 1: Test method |
| ISO/TS 4949:2016 | Steel names based on letter symbols |
| ISO/TR 9769:1991 | Steel and iron — Review of available methods of analysis |
| ISO 16143-3:2014 | Stainless steels for general purposes — Part 3: Wire |
| ISO 15510:2014 | Stainless steels — Chemical composition |
| ISO 16143-2:2014 | Stainless steels for general purposes — Part 2: Corrosion-resistant semi-finished products, bars, rods and sections |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| ISO 6892-1:2016 | Metallic materials — Tensile testing — Part 1: Method of test at room temperature |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| ISO 6931-2:2005 | Stainless steels for springs — Part 2: Narrow strip |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| ISO 4955:2016 | Heat-resistant steels |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| ISO 9328-1:2011 | Steel flat products for pressure purposes — Technical delivery conditions — Part 1: General requirements |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| ISO 6892-2:2011 | Metallic materials — Tensile testing — Part 2: Method of test at elevated temperature |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| ISO 9328-7:2011 | Steel flat products for pressure purposes — Technical delivery conditions — Part 7: Stainless steels |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.