14/30256269 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN ISO 24817 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
Hardcopy , PDF
English
31-08-2015
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Applications
6 Summary of key issues
7 Qualification and design
8 Installation
9 Testing and inspection
10 System testing
11 Decommissioning
Annex A (normative) - Design data sheet
Annex B (normative) - Qualification data
Annex C (normative) - Short-term pipe spool
survival test
Annex D (normative) - Measurement of
[gamma]LCL for through-wall defect
calculation
Annex E (normative) - Measurement of
performance test data
Annex F (normative) - Measurement of
impact performance
Annex G (normative) - Measurement of
the degradation factor
Annex H (informative) - Axial extent of
repair look-up table
Annex I (normative) - Installer qualification
Annex J (informative) - Installation requirements
and guidance
Annex K (informative) - Design considerations
Annex L (informative) - Management of the
integrity of composite repair systems
to pipework and vessels
Bibliography
BS EN ISO 24817.
| Committee |
PSE/17/-/6
|
| DocumentType |
Draft
|
| Pages |
94
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 15649:2001 | Petroleum and natural gas industries — Piping |
| AWWA M45 : 3 | FIBERGLASS PIPE DESIGN |
| ISO 527-4:1997 | Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| ASTM G 8 : 1996 | Standard Test Methods for Cathodic Disbonding of Pipeline Coatings |
| EN 59:2016 | Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester |
| ANSI/AWWA C200 : 2017 | STEEL WATER PIPE, 6 IN. (150 MM) AND LARGER |
| ASTM D 543 : 2014 : REDLINE | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ISO 15310:1999 | Fibre-reinforced plastic composites — Determination of the in-plane shear modulus by the plate twist method |
| BS 2782-10 Method 1001:1977 | Glass reinforced plastics measurement of hardness by means of a barcol impressor |
| AWWA C151/A21.51 : 2017 | DUCTILE-IRON PIPE, CENTRIFUGALLY CAST |
| ISO 11359-2:1999 | Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| AWWA C150/A21.50 : 2014 | THICKNESS DESIGN OF DUCTILE-IRON PIPE |
| AWWA M11 : 2004 | STEEL PIPE: A GUIDE FOR DESIGN AND INSTALLATION |
| ISO 11357-2:2013 | Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and glass transition step height |
| ASTM C 581 : 2015 : REDLINE | Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service |
| ASTM D 696 : 2016 : REDLINE | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ISO 10952:2014 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition |
| API 579-1 : 2016 | FITNESS-FOR-SERVICE |
| ISO 75-3:2004 | Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics |
| ASTM D 2992 : 2012 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| EN 1465:2009 | Adhesives - Determination of tensile lap-shear strength of bonded assemblies |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
| ISO 13623:2017 | Petroleum and natural gas industries — Pipeline transportation systems |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| ISO 14129:1997 | Fibre-reinforced plastic composites — Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by the plus or minus 45 degree tension test method |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.