• There are no items in your cart

15/30304408 DC : 0

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

BS EN ISO 20029-2 - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES

Available format(s)

Hardcopy , PDF

Superseded date

28-02-2018

Language(s)

English

Foreword
Introduction
1 Scope
2 Normative references
3 Preparation of test specimens
4 Conditioning of test specimens
5 Determination of properties
Annex A (informative) - Determination of tensile properties
Bibliography

BS EN ISO 20029-2.

Committee
PRI/82
DocumentType
Draft
Pages
28
PublisherName
British Standards Institution
Status
Superseded

IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 16365-2:2014 Plastics — Thermoplastic polyurethanes for moulding and extrusion — Part 2: Preparation of test specimens and determination of properties
ISO 22007-3:2008 Plastics Determination of thermal conductivity and thermal diffusivity Part 3: Temperature wave analysis method
ISO 22007-4:2017 Plastics — Determination of thermal conductivity and thermal diffusivity — Part 4: Laser flash method
ISO 974:2000 Plastics Determination of the brittleness temperature by impact
IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
ISO 815-1:2014 Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures
ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
ISO 8256:2004 Plastics — Determination of tensile-impact strength
ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
ISO 34-1:2015 Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11357-3:2011 Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 11357-4:2014 Plastics Differential scanning calorimetry (DSC) Part 4: Determination of specific heat capacity
ISO 294-4:2001 Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage
IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 15512:2016 Plastics Determination of water content
ISO 62:2008 Plastics Determination of water absorption
ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
ISO 22007-2:2015 Plastics Determination of thermal conductivity and thermal diffusivity Part 2: Transient plane heat source (hot disc) method
ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 20753:2008 Plastics Test specimens
ISO 178:2010 Plastics Determination of flexural properties
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)

€23.37
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.