15/30330403 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 50126-1 - RAILWAY APPLICATIONS - THE SPECIFICATION AND DEMONSTRATION OF RELIABILITY, AVAILABILITY, MAINTAINABILITY AND SAFETY (RAMS) - PART 1: GENERIC RAMS PROCESS
Hardcopy , PDF
06-12-2017
English
Important note : Users cannot be edited or removed once added to your Multi user PDF.
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviations
5 Railway RAMS
6 Management of Railway RAMS - General Requirements
7 RAMS life-cycle
8 Safety Case
Annex A (informative) - RAMS plan
Annex B (informative) - Examples of parameters for
railway
Annex C (intentionally left blank)
Annex D (informative) - Risk matrix calibration and
risk acceptance categories
Annex E (informative) - Guidance on system definition
Bibliography
BS EN 50126-1.
| Committee |
GEL/9
|
| DocumentType |
Draft
|
| Pages |
94
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 50126-1 : DRAFT 2015 | Identical |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| EN 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 61123:1991 | Reliability testing - Compliance test plans for success ratio |
| IEC 60605-4:2001 | Equipment reliability testing - Part 4: Statistical procedures for exponential distribution - Point estimates, confidence intervals, prediction intervals and tolerance intervals |
| IEC 60319:1999 | Presentation and specification of reliability data for electronic components |
| EN 60300-3-2:2005 | Dependability management - Part 3-2: Application guide - Collection of dependability data from the field |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 61014:2003 | Programmes for reliability growth |
| IEC 60605-6:2007 | Equipment reliability testing - Part 6: Tests for the validity and estimation of the constant failure rate and constant failure intensity |
| IEC 60706-3:2006 | Maintainability of equipment - Part 3: Verification and collection, analysis and presentation of data |
| IEC 61160:2005 | Design review |
| EN 60706-2:2006 | Maintainability of equipment - Part 2: Maintainability requirements and studies during the design and development phase |
| IEC 61070:1991 | Compliance test procedures for steady-state availability |
| IEC 61078:2016 | Reliability block diagrams |
| IEC 61165:2006 | Application of Markov techniques |
| IEC 60605-3-1:1986 | Equipment reliability testing. Part 3: Preferred test conditions. Indoor portable equipment - Low degree of simulation |
| EN 60706-3:2006 | Maintainability of equipment - Part 3: Verification and collection, analysis and presentation of data |
| EN 60300-3-1:2004 | Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology |
| EN 61078 : 1991 | RELIABILITY BLOCK DIAGRAMS (IEC 61078:2016) |
| IEC TR 62380:2004 | Reliability data handbook - Universal model for reliability prediction of electronics components, PCBs and equipment |
| EN 61165:2006 | Application of Markov techniques |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| IEC 60300-3-2:2004 | Dependability management - Part 3-2: Application guide - Collection of dependability data from the field |
| IEC 60300-3-1:2003 | Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| IEC 61703:2016 | Mathematical expressions for reliability, availability, maintainability and maintenance support terms |
| EN 61025:2007 | Fault tree analysis (FTA) |
| IEC 60706-1:1982 | Guide on maintainability of equipment. Part 1 - Sections One, Two and Three. Introduction, requirements and maintainability programme |
| IEC 60605-2:1994 | Equipment reliability testing - Part 2: Design of test cycles |
| ISO 9001:2015 | Quality management systems — Requirements |
| IEC 60706-2:2006 | Maintainability of equipment - Part 2: Maintainability requirements and studies during the design and development phase |
| EN 61014:2003 | Programmes for reliability growth |
| IEC 60706-5:2007 | Maintainability of equipment - Part 5: Testability and diagnostic testing |
| EN 61160:2005 | Design review |
| EN 61709:2017 | Electric components - Reliability - Reference conditions for failure rates and stress models for conversion |
| IEC 60706-6:1994 | Guide on maintainability of equipment - Part 6: Section 9: Statistical methods in maintainability evaluation |
| EN 60706-5:2007 | Maintainability of equipment - Part 5: Testability and diagnostic testing |
| EN 61703:2016 | Mathematical expressions for reliability, availability, maintainability and maintenance support terms |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.