AGA Z22302 : 2002 ADDENDA A 03

Chapter 1 - General
  1.1 Scope
  1.2 Alternative Materials, Equipment, and Procedures
  1.3 Retroactivity
  1.4 Qualified Agency
  1.5 Interruption of Service
  1.6 Prevention of Accidental Ignition
  1.7 Definitions
Chapter 2 - Gas Piping System Design, Materials, and
            Components
  2.1 Piping Plan
  2.2 Provision for Location of Point of Delivery
  2.3 Interconnections Between Gas Piping Systems
  2.4 Sizing of Gas Piping Systems
  2.5 Piping System Operating Pressure Limitations
  2.6 Acceptable Piping Materials and Joining Methods
  2.7 Gas Meters
  2.8 Gas Pressure Regulators
  2.9 Overpressure Protection Devices
  2.10 Back Pressure Protection
  2.11 Low-Pressure Protection
  2.12 Shutoff Valves
  2.13 Expansion and Flexibility
Chapter 3 - Gas Piping Installation
  3.1 Piping Underground
  3.2 Aboveground Piping Outside
  3.3 Piping in Buildings
  3.4 Concealed Piping in Buildings
  3.5 Piping in Vertical Chases
  3.6 Gas Pipe Turns
  3.7 Drips and Sediment Traps
  3.8 Outlets
  3.9 Branch Pipe Connection
  3.10 Manual Gas Shutoff Valves
  3.11 Prohibited Devices
  3.12 Systems Containing Gas-Air Mixtures Outside The
       Flammable Range
  3.13 Systems Containing Flammable Gas-Air Mixtures
  3.14 Electrical Bonding and Grounding
  3.15 Electrical Circuits
  3.16 Electrical Connections
Chapter 4 - Inspection, Testing, and Purging
  4.1 Pressure Testing and Inspection
  4.2 System and Equipment Leakage Test
  4.3 Purging
Chapter 5 - Equipment Installation
  5.1 General
  5.2 Accessibility and Clearance
  5.3 Air for Combustion and Ventilation
  5.4 Equipment on Roofs
  5.5 Equipment Connections to Building Piping
  5.6 Electrical
  5.7 Room Temperature Thermostats
Chapter 6 - Installation of Specific Equipment
  6.1 General
  6.2 Air-Conditioning Equipment (Gas-Fired Air Conditioners
       and Heat Pumps)
  6.3 Central Heating Boilers and Furnaces
  6.4 Clothes Dryers
  6.5 Conversion Burners
  6.6 Decorative Appliances for Installation in Vented
       Fireplaces
  6.7 Gas Fireplaces, Vented
  6.8 Direct Makeup Air Heaters
  6.9 Direct Gas-Fired Industrial Air Heaters
  6.10 Duct Furnaces
  6.11 Floor Furnaces
  6.12 Food Service Equipment, Floor-Mounted
  6.13 Food Service Equipment Counter Appliances
  6.14 Hot Plates and Laundry Stoves
  6.15 Household Cooking Appliances
  6.16 Illuminating Appliances
  6.17 Incinerators, Commercial-Industrial
  6.18 Incinerators, Domestic
  6.19 Infrared Heaters
  6.20 Open-Top Broiler Units
  6.21 Outdoor Cooking Appliances
  6.22 Pool Heaters
  6.23 Refrigerators
  6.24 Room Heaters
  6.25 Stationary Gas Engines
  6.26 Gas-Fired Toilets
  6.27 Unit Heaters
  6.28 Wall Furnaces
  6.29 Water Heaters
  6.30 Compressed Natural Gas (CNG) Vehicular Fuel Systems
  6.31 Appliances for Installation in Manufactured Housing
Chapter 7 - Venting of Equipment
  7.1 General
  7.2 Specification for Venting
  7.3 Design and Construction
  7.4 Type of Venting System to Be Used
  7.5 Masonry, Metal, and Factory-Built Chimneys
  7.6 Gas Vents
  7.7 Single-Wall Metal Pipe
  7.8 Through the Wall Vent Termination
  7.9 Condensation Drain
  7.10 Vent Connectors for Category I Gas Utilization Equipment
  7.11 Vent Connectors for Category II, Gas Category III, and
       Category IV Gas Utilization Equipment
  7.12 Draft Hoods and Draft Controls
  7.13 Manually Operated Dampers
  7.14 Automatically Operated Vent Dampers
  7.15 Obstructions
Chapter 8 - Procedures to be Followed to Place Equipment in
            Operation
  8.1 Adjusting the Burner Input
  8.2 Primary Air Adjustment
  8.3 Safety Shutoff Devices
  8.4 Automatic Ignition
  8.5 Protective Devices
  8.6 Checking the Draft
  8.7 Operating Instructions
Chapter 9 - Sizing Tables
  9.1 Tables for Sizing Gas Piping Systems
Chapter 10 - Sizing of Category I Venting Systems
  10.1 Additional Requirements to Single Appliance Vent Tables
       10.1 Through 10.5
  10.2 Additional Requirements to Multiple Appliance Vent
       Tables 10.6 Through 10.13(a) and (b)
Chapter 11 - Referenced Publications
Appendix A - Explanatory Material
Appendix B - Coordination of Gas Utilization Equipment Design,
             Construction, and Maintenance
Appendix C - Sizing and Capacities of Gas Piping
Appendix D - Suggested Method for Checking for Leakage
Appendix E - Suggested Emergency Procedures for Gas Leaks
Appendix F - Flow of Gas Through Fixed Orifices
Appendix G - Sizing of Venting Systems Serving Appliances
             Equipped with Draft Hoods, Category I Appliances,
             and Appliances Listed for Use with Type B Vents
Appendix H - Recommended Procedure for Safety Inspection of an
             Existing Appliance Installation
Appendix I - Recommended Procedure for Installing Electrically
             Operated Automatic Vent Damper Devices in Existing
             Vents
Appendix J - Recommended Procedure for Installing Mechanically
             Actuated Automatic Vent Damper Devices in Existing
             Vents
Appendix K - Recommended Procedure for Installing Thermally
             Actuated Automatic Vent Damper Devices in Existing
             Vents
Appendix L - Example of Air Opening Design for Combustion and
             Ventilation
Appendix M - Referenced Publications
Index

Covers safety code that applies to the installation of fuel gas utilization equipment and accessories including combustion, installation, ventilation, venting and piping system requirements. Also includes design, materials, components, fabrication assembly, installation, testing, inspection, operation and maintenance).