Skip to content
Please enter a keyword to search

  • API 19G4 : 2011

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PRACTICES FOR SIDE-POCKET MANDRELS AND RELATED EQUIPMENT

    Available format(s):  Hardcopy, PDF

    Superseded date:  18-02-2021

    Language(s):  English

    Published date:  01-01-2011

    Publisher:  American Petroleum Institute

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    API Foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Abbreviations and symbols
    5 Guidelines for application of side-pocket mandrels
      and related equipment
    Annex A (informative) - Interface compatibility issues
    Annex B (informative) - Test facilities for flow-control device
            performance testing
    Annex C (informative) - Set-up and calibration of flow-control
            devices
    Annex D (informative) - Pre-installation and post-removal
            inspection and testing
    Annex E (informative) - Reconditioning side-pocket mandrels and
             related equipment
    Annex F (informative) - Reconditioning shops and shop personnel
    Annex G (informative) - User/purchaser functional templates for
            side-pocket mandrels and related equipment
    Annex H (informative) - Supplier/manufacturer product data sheet
            templates for side-pocket mandrels and related equipment
    Bibliography

    Abstract - (Show below) - (Hide below)

    Gives informative documentation to assist the user/purchaser and the supplier/manufacturer in specification, design, selection, testing, calibration, reconditioning, installation and use of side-pocket mandrels, flow-control devices and associated latches and installation tools.

    General Product Information - (Show below) - (Hide below)

    Development Note Also numbered as ISO 17078-4. (06/2011)
    Document Type Standard
    Publisher American Petroleum Institute
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    API 14A : 2015 SPECIFICATION FOR SUBSURFACE SAFETY VALVE EQUIPMENT
    API 19G9 : 2015 DESIGN, OPERATION, AND TROUBLESHOOTING OF DUAL GAS-LIFT WELLS
    API 19G3 : 2011 RUNNING TOOLS, PULLING TOOLS, AND KICK-OVER TOOLS AND LATCHES FOR SIDE-POCKET MANDRELS
    API RP 19GLHB:2020+ADD 1:2023 Gas Lift Handbook

    Standards Referencing This Book - (Show below) - (Hide below)

    ASME PV CODE 8 DIV 2 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES
    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
    ASME PV CODE 9 : 2017 BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS
    ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
    API 19G1 : 2010 SIDE-POCKET MANDRELS
    ANSI/NCSL Z540 3 : 2006(R2013) REQUIREMENTS FOR THE CALIBRATION OF MEASURING AND TEST EQUIPMENT
    ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
    ISO 6508-1:2016 Metallic materials — Rockwell hardness test — Part 1: Test method
    ISO 14313:2007 Petroleum and natural gas industries — Pipeline transportation systems — Pipeline valves
    ASME B31.8 : 2016 Gas Transmission and Distribution Piping Systems
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    SAE AS 568 : 2014 AEROSPACE SIZE STANDARD FOR O-RINGS
    AGA REPORT 3-1 : 90 ERRATA 94 ORIFICE METERING OF NATURAL GAS AND OTHER RELATED HYDROCARBON FLUIDS - GENERAL EQUATIONS AND UNCERTAINTY GUIDELINES
    ASME B1.20.1 : 2013(R2018) PIPE THREADS, GENERAL PURPOSE (INCH)
    ISO 17078-3:2009 Petroleum and natural gas industries Drilling and production equipment Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels
    API 6D :2015 SPECIFICATION FOR PIPELINE AND PIPING VALVES
    ASME B16.5 : 2017 PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
    ASME B16.34 : 2017 VALVES - FLANGED, THREADED, AND WELDING END
    ASME PV CODE 5 : 2017 BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION
    API 19G3 : 2011 RUNNING TOOLS, PULLING TOOLS, AND KICK-OVER TOOLS AND LATCHES FOR SIDE-POCKET MANDRELS
    ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
    BS 2M 54:1991 Specification for temperature control in the heat treatment of metals
    ISO 17078-2:2007 Petroleum and natural gas industries — Drilling and production equipment — Part 2: Flow-control devices for side-pocket mandrels
    SAE AMS H 6875 : 2010 HEAT TREATMENT OF STEEL RAW MATERIALS
    ISO 17078-1:2004 Petroleum and natural gas industries — Drilling and production equipment — Part 1: Side-pocket mandrels
    MIL-STD-105 Revision E:1989 SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
    API 19G2 : 2010 FLOW-CONTROL DEVICES FOR SIDE-POCKET MANDRELS
    ISO 11960:2014 Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective