Skip to content
Please enter a keyword to search

  • API 19G3 : 2011

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    RUNNING TOOLS, PULLING TOOLS, AND KICK-OVER TOOLS AND LATCHES FOR SIDE-POCKET MANDRELS

    Available format(s):  Hardcopy, PDF

    Superseded date:  18-02-2021

    Language(s):  English

    Published date:  01-01-2011

    Publisher:  American Petroleum Institute

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    API Foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Functional specification
    6 Technical specification
    7 Supplier/manufacturer requirements
    Annex A (normative) - Requirements for running and pulling
                          tools
    Annex B (normative) - Requirements for kick-over tools
    Annex C (normative) - Requirements for latches
    Annex D (normative) - Side-pocket mandrel tool interface
                          evaluations
    Annex E (informative) - Figures
    Annex F (informative) - API Monogram Program
    Bibliography

    Abstract - (Show below) - (Hide below)

    Gives requirements and guidelines for running tools, pulling tools, kick-over tools and latches used for the installation and retrieval of flow control and other devices to be installed in side-pocket mandrels for use in the petroleum and natural gas industries.

    General Product Information - (Show below) - (Hide below)

    Development Note Also numbered as ISO 17078-3. (06/2011)
    Document Type Standard
    Publisher American Petroleum Institute
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    API 14A : 2015 SPECIFICATION FOR SUBSURFACE SAFETY VALVE EQUIPMENT
    API 19G4 : 2011 PRACTICES FOR SIDE-POCKET MANDRELS AND RELATED EQUIPMENT
    API 19G9 : 2015 DESIGN, OPERATION, AND TROUBLESHOOTING OF DUAL GAS-LIFT WELLS
    API RP 19GLHB:2020+ADD 1:2023 Gas Lift Handbook

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ISO 80000-4:2006 Quantities and units Part 4: Mechanics
    ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
    ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
    ASME PV CODE 9 : 2017 BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS
    API 19G1 : 2010 SIDE-POCKET MANDRELS
    ISO 17078-4:2010 Petroleum and natural gas industries — Drilling and production equipment — Part 4: Practices for side-pocket mandrels and related equipment
    ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
    ISO 6508-1:2016 Metallic materials — Rockwell hardness test — Part 1: Test method
    ISO 6892:1998 Metallic materials Tensile testing at ambient temperature
    ISO 31-0:1992 Quantities and units Part 0: General principles
    ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
    API 19G4 : 2011 PRACTICES FOR SIDE-POCKET MANDRELS AND RELATED EQUIPMENT
    ISO 3601-1:2012 Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes
    ISO 17078-2:2007 Petroleum and natural gas industries — Drilling and production equipment — Part 2: Flow-control devices for side-pocket mandrels
    SAE AMS H 6875 : 2010 HEAT TREATMENT OF STEEL RAW MATERIALS
    ISO 3601-3:2005 Fluid power systems O-rings Part 3: Quality acceptance criteria
    ISO 17078-1:2004 Petroleum and natural gas industries — Drilling and production equipment — Part 1: Side-pocket mandrels
    API 19G2 : 2010 FLOW-CONTROL DEVICES FOR SIDE-POCKET MANDRELS
    ISO 18265:2013 Metallic materials Conversion of hardness values
    ISO/IEC Guide 22:1996 General criteria for supplier's declaration of conformity
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective