AS/NZS 4114.2:2003

1 - AS/NZS 4114.2:2003 SPRAY PAINTING BOOTHS, DESIGNATED SPRAY PAINTING AREAS AND PAINT MIXING ROOMS - INSTALLATION AND...
4 - PREFACE
5 - CONTENTS
6 - SECTION 1 GENERAL
6 - 1.1 SCOPE
6 - 1.2 APPLICATION
6 - 1.3 REFERENCED DOCUMENTS
7 - 1.4 DEFINITIONS
7 - 1.4.1 Designated spray painting areas
7 - 1.5 DOCUMENTATION
8 - 1.6 QUALIFICATIONS OF PERSONNEL
8 - 1.7 AREA CLASSIFICATION
8 - 1.8 ENVIRONMENTAL CONDITIONS AND OTHER EXTERNAL INFLUENCES
9 - SECTION 2 INSTALLATION AND MAINTENANCE
9 - 2.1 SCOPE OF SECTION
9 - 2.2 AREAS ASSOCIATED WITH SPRAY PAINTING BOOTHS
9 - 2.3 DESIGNATED SPRAY PAINTING AREAS
9 - 2.3.1 Authorization
9 - 2.3.2 Documentation
9 - 2.3.3 Site preparation
9 - 2.3.4 Isolation of power
9 - 2.3.5 Training
9 - 2.3.6 Fire protection
9 - 2.3.7 Removal of personnel
9 - 2.3.8 Clean up procedure
9 - 2.3.9 Reclaim and containment of contaminates
10 - 2.3.10 Earthing/bonding
10 - 2.3.11 Security
10 - 2.3.12 Access
10 - 2.3.13 Personal protective equipment (PPE)
10 - 2.3.14 Signage
10 - 2.4 METHODS OF INSTALLATION
10 - 2.5 DUCTWORK
10 - 2.6 COMBUSTIBLE MATERIALS
10 - 2.7 LOCATION OF PAINT MIXING ROOMS
11 - 2.8 MAINTENANCE
11 - 2.9 MODIFICATIONS AND ALTERATIONS
12 - APPENDIX A - RELEVANT AUTHORITIES
12 - A1 SCOPE
12 - A2 AUTHORITIES IN AUSTRALIA
13 - A3 AUTHORITIES IN NEW ZEALAND
14 - APPENDIX B - INSPECTION, TESTING AND MAINTENANCE
14 - B1 SPECIAL INSPECTIONS FOR MOVABLE APPARATUS
14 - B2 INSPECTION CHECKS
14 - B2.1 General
14 - B2.2 Area classification
14 - B2.3 Modifications
14 - B2.4 Temperature class
14 - B2.5 Marking
14 - B2.6 Circuit identification
14 - B2.7 Lamps and fuses
14 - B2.8 Earthing and bonding
15 - B2.9 Electrical connections
15 - B2.10 Damage
15 - B2.11 Electrical protection
15 - B2.12 Compliance with documentation
15 - B3 MAINTENANCE
15 - B3.1 General
15 - B3.2 Check list
15 - B3.3 Removal of electrical apparatus
15 - B3.4 Air filters
15 - B3.5 Repair
16 - B3.6 Inspection after maintenance

Specifies requirements for the installation and maintenance of spray painting booths, designated spray painting areas and paint mixing rooms in which there may be an explosion hazard due to the presence of flammable volatiles from the paints and finishes used. It is intended to be read in conjunction with Part 1 and AS 2381.1.

This Standard sets out requirements for the installation and maintenance of spray painting booths and paint mixing rooms complying with AS/NZS 4114.1 and designated spray painting areas. A designated spray painting area is not for general use but is to be used only where the use of a spray painting booth is not practicable. This Standard is to be read in conjunction with AS/NZS 2381.1, which describes the fundamental considerations that affect the installation and maintenance of all electrical apparatus used in areas termed hazardous areas where an explosive atmosphere is likely to be present. Requirements for the design, construction and testing of spray painting booths and paint mixing rooms are given in AS/NZS 4114.1.

First published as part of AS/NZS 4114(Int):1993.Jointly revised and redesignated in part as AS/NZS 4114.2:1995.Second edition 2003. First published as part of AS/NZS 4114(Int):1993. Jointly revised and redesignated in part as AS/NZS 4114.2:1995. Second edition 2003.