ASTM C 1193 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Use of Joint Sealants
Hardcopy , PDF
25-05-2023
English
13-01-2016
Committee |
C 24
|
DocumentType |
Guide
|
Pages |
33
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied joint sealant and secondarily to a precured sealant when used with a properly prepared joint opening and substrate surfaces.
1.2An elastomeric or non-elastomeric sealant described by this guide should meet the requirements of Specification C834, C920, or C1311.
1.3This guide does not provide information or guidelines for the use of a sealant in a structural sealant glazing application. Guide C1401 should be consulted for this information. Additionally, it also does not provide information or guidelines for the use of a sealant in an insulating glass unit edge seal used in a structural sealant glazing application. Guide C1249 should be consulted for this information.
1.4Practice C919 should be consulted for information and guidelines for the use of a sealant in an application where an acoustic joint seal is required.
1.5This guide also does not provide information relative to the numerous types of sealant that are available nor specific generic sealant properties, such as hardness, tack-free time, or curing process, among others.
1.6The values stated in SI units are to be regarded as the standard. The values given in parenthesis are provided for information only.
1.7The Committee with jurisdiction for this standard is not aware of any comparable standards published by other organizations.
1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
1.9The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.
ASTM E 2435 : 2005 : R2020 | Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties |
ASTM E 2266 : 2022 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
ASTM C 1564 : 2020 | Standard Guide for Use of Silicone Sealants for Protective Glazing Systems |
ASTM C 981 : 2020 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
ASTM E 241 : 2020 | Standard Guide for Limiting Water-Induced Damage to Buildings |
ASTM E 3223/E3223M : 2020 | Standard Guide for Specifying and Testing Field-Constructed Exterior Building Wall System Mockups in New Construction |
ASTM C 1311 : 2014 | Standard Specification for Solvent Release Sealants |
ASTM C 1253 : 2014 : R2019 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
ASTM C 920 : 2018 | Standard Specification for Elastomeric Joint Sealants |
ASTM C 1127/C1127M : 2015 | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface |
ASTM E 2112 : 2019 : REV B | Standard Practice for Installation of Exterior Windows, Doors and Skylights |
ASTM C 1472 : 2016 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 898/C898M : 2009 : R2017 | Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Separate Wearing Course |
ASTM E 2266 : 2011 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
ASTM C 919 : 2019 | Standard Practice for Use of Sealants in Acoustical Applications |
ASTM C 1736 : 2011 | Standard Practice for Non-Destructive Evaluation of Adhesion of Installed Weatherproofing Sealant Joints Using a Rolling Device (Withdrawn 2020) |
ASTM C 1242 : 2019 | Standard Guide for Selection, Design, and Installation of Dimension Stone Attachment Systems |
ASTM E 2435 : 2005 : R2015 | Standard Guide for Application of Engineering Controls to Facilitate Use or Redevelopment of Chemical-Affected Properties |
ASTM E 241 : 2009 : R2014 : EDT 1 | Standard Guide for Limiting Water-Induced Damage to Buildings |
ASTM C 1521 : 2013 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 834 : 2017 | Standard Specification for Latex Sealants |
ASTM C 1564 : 2015 | Standard Guide for Use of Silicone Sealants for Protective Glazing Systems |
ASTM C 981 : 2005 : R2013 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
ASTM C 1481 : 2012 : R2017 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 1401 : 2014 | Standard Guide for Structural Sealant Glazing |
ASTM C 717 : 2019 | Standard Terminology of Building Seals and Sealants |
ASTM C 1681 : 2018 | Standard Test Method for Evaluating the Tear Resistance of a Sealant Under Constant Strain |
ASTM C 1257 : 1994 | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM C 711 : 2022 | Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants |
ASTM C 1382 : 2002 | Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM C 1481 : 2011 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 792 : 2023 | Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants |
ASTM C 1401 : 1998 | Standard Guide for Structural Sealant Glazing |
ASTM C 1519 : 2010 | Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
ASTM C 1184 : 2000 : REV A | Standard Specification for Structural Silicone Sealants |
ASTM C 1481 : 2012 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 1401 : 2009 | Standard Guide for Structural Sealant Glazing |
ASTM C 794 : 2018 | Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants |
ASTM E 2114 : 2005 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 719 : 2022 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
ASTM C 1083 : 2006 : R2020 : EDT 1 | Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials |
ASTM C 1442 : 2011 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM C 1248 : 2004 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM C 1330 : 2002 : R2013 | Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants |
ASTM C 1241 : 2000 : R2009 | Standard Test Method for Volume Shrinkage of Latex Sealants During Cure |
ASTM C 1472 : 2005 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 1401 : 2009 : REV A | Standard Guide for Structural Sealant Glazing |
ASTM D 2203 : 2001 : R2023 | Standard Test Method for Staining from Sealants |
ASTM C 1519 : 2004 | Standard Practice for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
ASTM C 661 : 2015 : R2022 | Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer |
ASTM C 1184 : 2018 : EDT 1 | Standard Specification for Structural Silicone Sealants |
ASTM E 2114 : 2005 : REV A | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1330 : 1996 | Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants |
ASTM C 1521 : 2009 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM E 2114 : 2019 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1401 : 2014 : R2022 | Standard Guide for Structural Sealant Glazing |
ASTM C 1253 : 1993 : R1998 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
ASTM C 1241 : 2014 | Standard Test Method for Volume Shrinkage of Latex Sealants During Cure |
ASTM C 1087 : 2023 | Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems |
ASTM C 1472 : 2010 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 1265 : 1994 : R2011 | Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications |
ASTM C 1253 : 2014 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
ASTM C 1681 : 2014 | Standard Test Method for Evaluating the Tear Resistance of a Sealant Under Constant Strain |
ASTM C 1369 : 2007 | Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units |
ASTM C 1330 : 2002 | Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants |
ASTM C 1135 : 2000 : R2011 | Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants |
ASTM C 1472 : 2006 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 1382 : 2011 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM C 731 : 2015 : R2022 | Standard Test Method for Extrudability, After Package Aging, of Latex Sealants |
ASTM C 1401 : 2014 | Standard Guide for Structural Sealant Glazing |
ASTM C 1311 : 2002 | Standard Specification for Solvent Release Sealants |
ASTM C 1083 : 2006 : R2011 | Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials |
ASTM C 1216 : 1992 : R1997 | Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants |
ASTM C 1472 : 2016 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 1184 : 2018 | Standard Specification for Structural Silicone Sealants |
ASTM C 1087 : 2000 | Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems |
ASTM D 2453 : 2003 | Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds |
ASTM D 2203 : 2001 : R2007 | Standard Test Method for Staining from Sealants |
ASTM C 731 : 2015 | Standard Test Method for Extrudability, After Package Aging, of Latex Sealants |
ASTM C 661 : 2015 | Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer |
ASTM C 1083 : 2006 : R2015 | Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials |
ASTM C 1265 : 1994 : R2005 : EDT 1 | Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications |
ASTM C 834 : 2017 : R2023 | Standard Specification for Latex Sealants |
ASTM C 1311 : 1995 | Standard Specification for Solvent Release Sealants |
ASTM C 1241 : 2000 : R2005 | Standard Test Method for Volume Shrinkage of Latex Sealants During Cure |
ASTM C 1248 : 2008 : R2012 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM C 1253 : 2014 : R2019 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM C 1257 : 2006 | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM C 1330 : 2002 : R2007 | Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants |
ASTM C 919 : 2022 | Standard Practice for Use of Sealants in Acoustical Applications |
ASTM C 1369 : 2019 | Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units |
ASTM C 1135 : 2019 | Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants |
ASTM C 1249 : 2006 | Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications |
ASTM C 1253 : 1993 : R2009 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
ASTM E 2114 : 2006 : REV A | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1265 : 2017 | Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications |
ASTM C 1248 : 2006 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM C 1521 : 2009 : EDT 1 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 1369 : 2007 : R2014 | Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units |
ASTM E 2114 : 2001 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1311 : 2010 | Standard Specification for Solvent Release Sealants |
ASTM C 1248 : 2022 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM C 1311 : 2014 | Standard Specification for Solvent Release Sealants |
ASTM C 1216 : 2003 : R2008 | Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants |
ASTM C 1442 : 2014 : R2021 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM C 1257 : 2006 : REV A | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM E 2114 : 2004 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1247 : 2014 | Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids |
ASTM C 1521 : 2008 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 1247 : 2009 | Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids |
ASTM C 1519 : 2002 | Standard Practice for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
ASTM D 2203 : 2001 : R2018 | Standard Test Method for Staining from Sealants |
ASTM E 2114 : 2017 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1184 : 2000 : REV A : EDT 1 | Standard Specification for Structural Silicone Sealants |
ASTM C 1135 : 2000 : R2005 | Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants |
ASTM C 1472 : 2016 : R2022 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 732 : 2017 : R2022 | Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants |
ASTM D 2203 : 1993 | Standard Test Method for Staining from Sealants |
ASTM C 1442 : 2014 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM C 1247 : 1998 | Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids |
ASTM C 1249 : 2018 : R2023 | Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications |
ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM C 1521 : 2002 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 1442 : 2006 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM D 2453 : 2015 | Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds |
ASTM C 1135 : 2000 | Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants |
ASTM C 794 : 2018 : R2022 | Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants |
ASTM C 1382 : 2005 | Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM C 1135 : 2015 | Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants |
ASTM C 711 : 2014 | Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants |
ASTM D 2203 : 2001 : R2011 | Standard Test Method for Staining from Sealants |
ASTM E 2114 : 2023 | Standard Terminology for Sustainability |
ASTM C 1249 : 1993 | Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications |
ASTM C 1521 : 2019 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM D 2453 : 1999 | Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds |
ASTM C 719 : 2014 : R2019 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
ASTM C 1087 : 2016 | Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems |
ASTM C 1521 : 2008 : REV A | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 1519 : 2002 : REV A | Standard Practice for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
ASTM E 2114 : 2008 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 732 : 2017 | Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants |
ASTM C 1265 : 1994 : R1999 | Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications |
ASTM D 2453 : 2015 : R2020 : EDT 1 | Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds |
ASTM C 1257 : 2004 | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM C 1087 : 2000 : R2011 | Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems |
ASTM C 1481 : 2000 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 1442 : 2003 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM C 792 : 2015 : R2020 | Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants |
ASTM C 1521 : 2002 : REV A | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 793 : 2023 | Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants |
ASTM E 2114 : 2006 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1519 : 2010 : R2017 | Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
ASTM C 1481 : 2000 : R2006 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 1521 : 2019 : R2020 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 1249 : 2018 | Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications |
ASTM C 1481 : 2012 : R2017 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
ASTM C 1083:2006 | Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials |
ASTM C 1311 : 2022 | Standard Specification for Solvent Release Sealants |
ASTM C 1257 : 2015 | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM C 1472 : 2016 : EDT 1 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 1247 : 2020 | Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids |
ASTM C 1241 : 2014 : R2022 | Standard Test Method for Volume Shrinkage of Latex Sealants During Cure |
ASTM C 1248 : 2018 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM C 1401 : 2002 | Standard Guide for Structural Sealant Glazing |
ASTM C 1382 : 1997 | Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM C 1382 : 2004 | Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM C 1401 : 2007 | Standard Guide for Structural Sealant Glazing |
ASTM C 510 : 2016 | Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants |
ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM C 1257 : 2006 : REV A : R2012 | Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
ASTM C 1216 : 2003 | Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants |
ASTM C 1369 : 1997 | Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units |
ASTM C 1382 : 2016 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM C 1369 : 2002 | Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units |
ASTM C 1681 : 2009 | Standard Test Method for Evaluating the Tear Resistance of a Sealant Under Constant Strain |
ASTM E 2114 : 2021 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1265 : 2022 | Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications |
ASTM C 1184 : 2005 | Standard Specification for Structural Silicone Sealants |
ASTM C 510 : 2016 : R2022 | Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants |
ASTM C 1241 : 2000 | Standard Test Method for Volume Shrinkage of Latex Sealants During Cure |
ASTM C 1521 : 2013 | Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints |
ASTM C 793 : 2005 : R2017 | Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants |
ASTM C 1442 : 1999 | Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus |
ASTM C 1248 : 2008 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM C 1087 : 2000 : R2006 : EDT 1 | Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems |
ASTM C 1087 : 2000 : R2006 | Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems |
ASTM C 1083 : 2000 | Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials |
ASTM C 1472 : 2000 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
ASTM C 1519 : 2010 : R2022 | Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
ASTM C 1184 : 2013 | Standard Specification for Structural Silicone Sealants |
ASTM E 2114 : 2000 : REV A | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM C 1184 : 2014 | Standard Specification for Structural Silicone Sealants |
ASTM C 1382 : 2016 : R2023 | Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints |
ASTM D 2203 : 2001 | Standard Test Method for Staining from Sealants |
ASTM C 1248 : 1993 : R1998 | Standard Test Method for Staining of Porous Substrate by Joint Sealants |
ASTM C 1253 : 1993 : R2005 | Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
ASTM D 2453 : 2003 : R2009 | Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds |
ASTM C 1330 : 2018 | Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants |
ASTM C 1249 : 2006 : REV A | Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications |
ASTM C 1249 : 2006 : REV A : R2010 | Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.