ASTM D 1003 : 2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
Available format(s)
Hardcopy , PDF
Superseded date
11-06-2021
Superseded by
Language(s)
English
Published date
28-11-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.This test method covers the evaluation of specific light-transmitting and wide-angle-light-scattering properties of planar sections of materials such as essentially transparent plastic.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the evaluation of specific light-transmitting and wide-angle-light-scattering properties of planar sections of materials such as essentially transparent plastic. Two procedures are provided for the measurement of luminous transmittance and haze. Procedure A uses a hazemeter as described in Section 5 and Procedure B uses a spectrophotometer as described in Section 8. Material having a haze value greater than 30 % is considered diffusing and should be tested in accordance with Practice E2387.
1.2The values stated in SI units are to be regarded as standard.
Note 1—For greater discrimination among materials that scatter a high percent of light within a narrow forward angle, such as is the case with abraded transparent plastics, adjust the hazemeter and perform measurements in accordance with Test Method D1044.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2—This test method is not equivalent to ISO 13468-1 and ISO/DIS 14782.
| ASTM F 790 : 2018 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM F 520 : 2021 | Standard Test Method for Environmental Resistance of Aerospace Transparencies to Artificially Induced Exposures |
| ASTM F 1863 : 2016 : R2021 | Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM F 1164 : 2019 | Standard Test Method for Evaluation of Transparent Plastics Exposed to Accelerated Weathering Combined with Biaxial Stress |
| ASTM F 2097 : 2020 | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM F 1864 : 2021 | Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings |
| ASTM F 2812 : 2012 : R2018 | Standard Specification for Goggle- and Spectacle-Type Eye Protectors for Selected Motor Sports (Withdrawn 2024) |
| ASTM F 513 : 2012 : R2018 | Standard Specification for Eye and Face Protective Equipment for Hockey Players |
| ASTM C 1900 : 2020 | Standard Practice for Weathering and Evaluation of Laminated Glass |
| ASTM F 803 : 2019 | Standard Specification for Eye Protectors for Selected Sports |
| ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 5436 : 2015 : R2020 | Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes |
| ASTM F 1776 : 2019 | Standard Specification for Eye Protective Devices for Paintball Sports |
| ASTM D 4649 : 2020 | Standard Guide for Use of Stretch Films and Wrapping Application |
| ASTM F 659 : 2010 : R2018 | Standard Specification for Ski and Snowboard Goggles (Withdrawn 2024) |
| ASTM D 706 : 2020 | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
| ASTM F 803 : 2014 | Standard Specification for Eye Protectors for Selected Sports |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM F 942 : 2018 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| ASTM D 3981 : 2009 : REV A : R2016 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM G 21 : 2015 | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
| ASTM F 3077 : 2017 | Standard Specification for Eye Protectors for Women’s Lacrosse |
| ASTM D 4802 : 2016 | Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet |
| ASTM F 2097 : 2016 | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM F 1164 : 1997 : R2014 | Standard Test Method for Evaluation of Transparent Plastics Exposed to Accelerated Weathering Combined with Biaxial Stress |
| ASTM D 706 : 2015 | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
| ASTM E 772 : 2015 | Standard Terminology of Solar Energy Conversion |
| ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 735 : 2017 | Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method |
| ASTM D 1562 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
| ASTM C 1349 : 2017 | Standard Specification for Architectural Flat Glass Clad Polycarbonate |
| ASTM E 1348 : 2015 : EDT 1 | Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM F 997 : 2018 | Standard Specification for Polycarbonate Resin for Medical Applications |
| ASTM D 5436 : 2015 | Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes |
| ASTM D 2673 : 2014 | Standard Specification for Oriented Polypropylene Film |
| ASTM E 1164 : 2012 : R2017 : EDT 1 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM F 1863 : 2016 | Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts |
| ASTM E 284 : 2017 | Standard Terminology of Appearance |
| ASTM D 4649 : 2003 : R2016 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ASTM E 2952 : 2017 | Standard Specification for Air-Purifying Respiratory Protective Smoke Escape Devices (RPED) |
| ASTM F 2879 : 2019 | Standard Specification for Eye Protective Devices for Airsoft Sports |
| ASTM F 2713 : 2018 | Standard Specification for Eye Protectors for Field Hockey |
| ASTM D 707 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
| ASTM D 4635 : 2016 | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 2103 : 2015 | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 788 : 2016 | Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
| ASTM D 5577 : 2019 | Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics |
| ASTM G 73 : 2010 : R2017 | Standard Test Method for Liquid Impingement Erosion Using Rotating Apparatus |
| ASTM D 1044 : 2013 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
| ASTM D 1746 : 2015 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM D 883 : 2019 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 8195 : 2018 | Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4673 : 2016 | Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials |
| ASTM F 1316 : 2018 | Standard Test Method for Measuring the Transmissivity of Transparent Parts |
| ASTM E 179 : 2017 | Standard Guide for Selection of Geometric Conditions for Measurement of Reflection and Transmission Properties of Materials |
| ASTM F 1864 : 2016 | Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings |
| ASTM F 520 : 2016 | Standard Test Method for Environmental Resistance of Aerospace Transparencies to Artificially Induced Exposures |
| ASTM E 259 : 1998 | Standard Practice for Preparation of Pressed Powder White Reflectance Factor Transfer Standards for Hemispherical Geometry and Bi-Directional Geometries |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2387 : 2005 | Standard Practice for Goniometric Optical Scatter Measurements |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 1044 : 2013 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
| ASTM E 2387 : 2005 : R2011 | Standard Practice for Goniometric Optical Scatter Measurements |
| ASTM D 1044 : 2005 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 1044 : 2008 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
| ASTM D 1044 : 2008 : EDT 1 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
| ASTM D 1044 : 1999 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
| ASTM D 1044 : 2019 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion by the Taber Abraser |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.