ASTM D 1005 : 1995 : R2020
Current
The latest, up-to-date edition.
Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
Hardcopy , PDF
English
01-06-2020
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers the measurement of film thickness of dried films of paint, varnish, lacquer, and related products using micrometers. Procedures A and B utilize stationary micrometers and Procedures C and D, hand-held micrometers. Procedures A and C are not recommended for films less than 12.5 μm (0.5 mils) in thickness. The minimum thickness required for Procedures B and D is a function of that required to enable removal of the sample as a free film.
1.2The procedures appear as follows:
1.2.1Procedure A—Stationary micrometer for measuring coatings applied to plane rigid surfaces.
1.2.2Procedure B—Stationary micrometer for measuring free films.
1.2.3Procedure C—Hand-held micrometer for measuring coatings applied to plane rigid surfaces.
1.2.4Procedure D—Hand-held micrometer for measuring free films.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM D 4060 : 2019 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 5178 : 2016 | Standard Test Method for Mar Resistance of Organic Coatings |
| ASTM E 1797 : 2012 : R2017 : EDT 1 | Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 2134 : 2019 | Standard Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker |
| ASTM A 1003/A1003M : 2015 | Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members |
| ASTM D 7187 : 2020 | Standard Test Method for Measuring Mechanistic Aspects of Scratch/Mar Behavior of Paint Coatings by Nanoscratching |
| ASTM D 2091 : 1996 : R2017 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 3170/D3170M : 2014 | Standard Test Method for Chipping Resistance of Coatings |
| ASTM D 1653 : 2013 | Standard Test Methods for Water Vapor Transmission of Organic Coating Films |
| ASTM A 742/A742M : 2020 | Standard Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe |
| ASTM D 7394 : 2018 | Standard Practice for Rheological Characterization of Architectural Coatings using Three Rotational Bench Viscometers |
| ASTM D 6037 : 2018 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
| ASTM A 755/A755M : 2018 | Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products |
| ASTM D 6803 : 2019 | Standard Practice for Testing and Sampling of Volatile Organic Compounds (Including Carbonyl Compounds) Emitted from Architectural Coatings Using Small-Scale Environmental Chambers |
| ASTM D 2197 : 2016 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 5087 : 2002 : R2014 | Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
| ASTM D 4366 : 2016 | Standard Test Methods for Hardness of Organic Coatings by Pendulum Damping Tests |
| ASTM D 4708 : 2019 | Standard Practice for Preparation of Uniform Free Films of Organic Coatings |
| ASTM F 3078 : 2015 | Standard Test Method for Identification and Quantification of Lead in Paint and Similar Coating Materials using Energy Dispersive X-ray Fluorescence Spectrometry (EDXRF) |
| ASTM D 6903 : 2007 : R2013 | Standard Test Method for Determination of Organic Biocide Release Rate From Antifouling Coatings in Substitute Ocean Water |
| ASTM E 1796 : 2003 : R2016 | Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 5498 : 2012 : REV A : R2018 | Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities |
| ASTM D 2248 : 2001 : REV A : R2018 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 4138 : 2007 : REV A : R2017 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM A 849 : 2015 | Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe |
| ASTM D 6279 : 2015 | Standard Test Method for Rub Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 3322 : 1982 : R2017 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 6762 : 2018 | Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings |
| ASTM D 5590 : 2017 | Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Fungal Defacement by Accelerated Four-Week Agar Plate Assay |
| ASTM D 968 : 2017 | Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive |
| ASTM D 6695 : 2016 | Standard Practice for Xenon-Arc Exposures of Paint and Related Coatings |
| ASTM C 1349 : 2017 | Standard Specification for Architectural Flat Glass Clad Polycarbonate |
| ASTM D 6132 : 2013 : R2017 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 2370 : 2016 | Standard Test Method for Tensile Properties of Organic Coatings |
| ASTM D 522/D522M : 2017 | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| ASTM D 2803 : 2009 : R2015 | Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal |
| ASTM A 762/A762M : 2019 | Standard Specification for Corrugated Steel Pipe, Polymer Precoated for Sewers and Drains |
| ASTM E 1795 : 2017 | Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 6669 : 2019 | Standard Practice for Selecting and Constructing Exposure Scenarios for Assessment of Exposures to Alkyd and Latex Interior Paints |
| ASTM D 6577 : 2015 : R2019 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 3730 : 2017 | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
| ASTM D 823 : 2018 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM D 6442 : 2006 : R2012 | Standard Test Method for Determination of Copper Release Rate From Antifouling Coatings in Substitute Ocean Water |
| ASTM D 6486 : 2001 : R2017 | Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings |
| ASTM D 7377 : 2009 : R2018 | Standard Practice for Evaluating the Water Wash-Off Resistance of Traffic Paints using a Water Faucet |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 333 : 2001 : R2013 | Standard Guide for Clear and Pigmented Lacquers |
| ASTM D 823 : 2018 : R2022 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM D 2370 : 2016 : R2021 | Standard Test Method for Tensile Properties of Organic Coatings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.