• Shopping Cart
    There are no items in your cart

ASTM D 115 : 2017

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation

Available format(s)

Hardcopy , PDF

Superseded date

04-04-2024

Language(s)

English

Published date

14-11-2017

€67.30
Excluding VAT

Committee
D 09
DocumentType
Test Method
Pages
9
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1These test methods cover tests for solvent containing varnishes primarily intended to provide electrical, mechanical, and chemical protection for electrical equipment. These test methods include tests for control and performance as follows:

Procedure

Section

Build

38 – 42

Dielectric Strength

43 – 48

Drainage

26 – 32

Flash Point

18 – 20

Nonvolatile Matter

21 – 25

Oil Resistance

54 – 56

Preparation of Test Specimens

    7

Specific Gravity

9 – 12

Temperature Index

4950

Time of Drying

33 – 37

Varnish Compatibility

51 – 53

Viscosity

13 – 17

1.2Where the entire test method is included in this standard, the precision and bias are not known unless given in the stated method.

1.3The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5.

Note 1:There is no equivalent IEC standard.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 2832 : 1992 : R2016 Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings
ASTM D 1711 : 2024 Standard Terminology Relating to Electrical Insulation
ASTM D 1304 : 1999 : R2020 : EDT 1 Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation
ASTM D 4882 : 2017 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Twisted-Coil Test
ASTM D 6053 : 2014 : R2018 Standard Test Method for Determination of Volatile Organic Compound (VOC) Content of Electrical Insulating Varnishes
ASTM D 4733 : 2017 Standard Test Methods for Solventless Electrical Insulating Varnishes
ASTM D 7230 : 2006 : R2021 Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
ASTM D 3955 : 2020 Standard Specification for Electrical Insulating Varnishes
ASTM D 4209 : 2007 : R2019 Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes
ASTM D 2756 : 2007 : R2017 Standard Test Method for Weight Loss of Electrical Insulating Varnishes
ASTM D 1084 : 2016 : R2021 Standard Test Methods for Viscosity of Adhesives

ASTM D 3251 : 1999 Standard Test Method for Thermal-Aging Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
ASTM D 202 : 2017 Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
ASTM D 5423 : 1993 : R2005 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation (Withdrawn 2014)
ASTM D 3251 : 2003 Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
ASTM D 3278 : 2020 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 1475 : 2013 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 1475 : 1998 : R2012 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 1932 : 2013 Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
ASTM D 1932 : 2018 Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
ASTM D 3145 : 2003 Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method
ASTM D 5423 : 2022 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
ASTM D 1932 : 2019 Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
ASTM D 2519 : 2001 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 3487 : 2016 Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus
ASTM D 1475 : 1985 Standard Test Method for Density of Paint, Varnish, Lacquer, and Related Products
ASTM D 3278 : 1996 : EDT 1 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 93 : 2019 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 202 : 1997 Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
ASTM D 1475 : 1998 : R2003 Standard Test Method for Density of Liquid Coatings, Inks, and Related Products
ASTM D 287 : 2022 Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer/Method)
ASTM D 3251 : 2004 : R2013 Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
ASTM D 3145 : 2008 Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method
ASTM D 93 : 1990 : EDT 1 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester
ASTM D 3251 : 2019 Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
ASTM D 3278 : 1982 : EDT 1 Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus
ASTM D 3278 : 2021 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 1932 : 2001 Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
ASTM D 3487 : 2000 Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus
ASTM D 5423 : 2023 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
ASTM D 56 : 2021 : REV A Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 2519 : 2007 : R2012 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 1932 : 1997 Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
ASTM D 202 : 2023 Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
ASTM D 1475 : 1960 : R1968 Standard Method Of Test For Density Of Paint, Varnish, Lacquer, And Related Products
ASTM D 2519 : 2019 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 56 : 2016 : REV A Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 1932 : 2004 : R2009 Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
ASTM D 5032 : 2011 Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions
ASTM D 1475 : 1998 : R2008 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 2519 : 2007 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 3487 : 2008 Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus
ASTM D 3251 : 2004 : R2009 Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
ASTM D 287 : 2012 : REV B Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)
ASTM D 2518 : 1999 Standard Specification for Woven Glass Fabrics for Electrical Insulation
ASTM D 3487 : 2009 Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus
ASTM D 3251 : 2004 Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire
ASTM D 56 : 2021 Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 3487 : 2000 : R2006 Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus
ASTM D 93 : 2000 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 2519 : 2002 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 3487 : 1988 : R1993 Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus
ASTM D 93 : 1985 Standard Test Method for Flash Point by Pensky-Martens Closed Tester
ASTM D 2518 : 1999 : R2004 Standard Specification for Woven Glass Fabrics for Electrical Insulation (Withdrawn 2013)
ASTM D 2519 : 2019 : REV A Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 5032 : 2019 Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions
ASTM D 3487 : 2016 : EDT 1 Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus
ASTM D 56 : 2022 Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 1932 : 2003 Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
ASTM D 2519 : 2018 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 3145 : 1997 Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method
ASTM D 56 : 1987 Standard Test Method for Flash Point by Tag Closed Tester
ASTM D 3145 : 2013 Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method
ASTM D 3145 : 2001 Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method
ASTM D 5032 : 1997 Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions
ASTM D 2519 : 1996 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
ASTM D 1475 : 1998 Standard Test Method for Density of Liquid Coatings, Inks, and Related Products
ASTM D 3278 : 1996 : R2004 : EDT 1 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
ASTM D 1932 : 2004 Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
ASTM D 93 : 1997 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 5423 : 1993 : R1999 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
ASTM D 3278 : 1996 : R2011 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus (Withdrawn 2020)
ASTM D 5423 : 2014 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
ASTM D 93 : 2018 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 287 : 2012 : REV B : R2019 Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)
ASTM D 3145 : 2018 Standard Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.