ASTM D 1203 : 2022
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Volatile Loss from Plastics Using Activated Carbon Methods
Hardcopy , PDF
29-11-2023
English
12-09-2022
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover the determination of volatile loss from a plastic material under defined conditions of time and temperature, using activated carbon as the immersion medium.
1.2Two test methods are covered as follows:
1.2.1Test Method A, Direct Contact with Activated Carbon—In this test method the plastic material is in direct contact with the carbon. This test method is particularly useful in the rapid comparison of a large number of plastic specimens.
1.2.2Test Method B, Wire Cage—This test method prescribes the use of a wire cage, which prevents direct contact between the plastic material and the carbon. By eliminating the direct contact, the migration of the volatile components to the surrounding carbon is minimized and loss by volatilization is more specifically measured.
1.3The values stated in SI units are to be regarded as the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:This standard and ISO 176 address the same subject matter, but differ in technical content.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8065/D8065M : 2016 : R2023 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM D 4551 : 2022 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane |
| ASTM D 1593 : 2022 | Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting |
| ASTM D 7176 : 2022 | Standard Specification for Non-Reinforced Polyvinyl Chloride (PVC) Geomembranes Used in Buried Applications |
| ASTM D 4000 : 2023 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 7176 : 2006 : R2018 | Standard Specification for Non-Reinforced Polyvinyl Chloride (PVC) Geomembranes Used in Buried Applications |
| ASTM D 3690 : 2019 | Standard Performance Specification for Vinyl-Coated and Urethane-Coated Upholstery Fabrics—Indoor |
| ASTM D 2287 : 2019 | Standard Classification System and Basis for Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds |
| ASTM D 5926 : 2015 : R2020 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4068 : 2017 : R2022 | Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane |
| ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM E 617 : 2023 | Standard Specification for Laboratory Weights and Precision Mass Standards |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 617 : 2013 | Standard Specification for Laboratory Weights and Precision Mass Standards |
| ASTM E 617 : 2018 | Standard Specification for Laboratory Weights and Precision Mass Standards |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.