• There are no items in your cart

ASTM D 1557 : 2012

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3))

Available format(s)

Hardcopy , PDF

Superseded date

12-05-2023

Language(s)

English

Published date

01-05-2012

€74.48
Excluding VAT

CONTAINED IN VOL. 04.08, 2017 Defines laboratory compaction methods used to determine the relationship between molding water content and dry unit weight of soils (compaction curve) compacted in a 4- or 6-in. (101.6- or 152.4-mm) diameter mold with a 10.00-lbf. (44.48-N) rammer dropped from a height of 18.00 in. (457.2 mm) producing a compactive effort of 56000 ft-lbf/ft[3] (2700 kN-m/m[3]).

Committee
D 18
DocumentType
Test Method
Pages
14
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1 These test methods cover laboratory compaction methods used to determine the relationship between molding water content and dry unit weight of soils (compaction curve) compacted in a 4- or 6-in. (101.6- or 152.4-mm) diameter mold with a 10.00-lbf. (44.48-N) rammer dropped from a height of 18.00 in. (457.2 mm) producing a compactive effort of 56 000 ft-lbf/ft3 (2700 kN-m/m3).

Note 1—The equipment and procedures are the same as proposed by the U.S. Corps of Engineers in 1945. The modified effort test (see 3.1.2) is sometimes referred to as the Modified Proctor Compaction Test.

1.1.1 Soils and soil-aggregate mixtures are to be regarded as natural occurring fine- or coarse-grained soils, or composites or mixtures of natural soils, or mixtures of natural and processed soils or aggregates such as gravel or crushed rock. Hereafter referred to as either soil or material.

1.2 These test methods apply only to soils (materials) that have 30 % or less by mass of their particles retained on the ¾-in. (19.0-mm) sieve and have not been previously compacted in the laboratory; that is, do not reuse compacted soil.

1.2.1 For relationships between unit weights and molding water contents of soils with 30 % or less by weight of material retained on the ¾ -in. (19.0-mm) sieve to unit weights and molding water contents of the fraction passing the ¾ -in. (19.0-mm) sieve, see Practice D4718.

1.3 Three alternative methods are provided. The method used shall be as indicated in the specification for the material being tested. If no method is specified, the choice should be based on the material gradation.

1.3.1 Method A:

1.3.1.1 Mold4-in. (101.6-mm) diameter.

1.3.1.2 MaterialPassing No. 4 (4.75-mm) sieve.

1.3.1.3 LayersFive.

1.3.1.4 Blows per layer25.

1.3.1.5 UsageMay be used if 25 % or less by mass of the material is retained on the No. 4 (4.75-mm) sieve. However, if 5 to 25 % by mass of the material is retained on the No. 4 (4.75-mm) sieve, Method A can be used but oversize corrections will be required (See 1.4) and there are no advantages to using Method A in this case.

1.3.1.6 Other UseIf this gradation requirement cannot be met, then Methods B or C may be used.

1.3.2 Method B:

1.3.2.1 Mold4-in. (101.6-mm) diameter.

1.3.2.2 MaterialPassing 3/8-in. (9.5-mm) sieve.

1.3.2.3 LayersFive.

1.3.2.4 Blows per layer25.

1.3.2.5 UsageMay be used if 25 % or less by mass of the material is retained on the 3/8-in. (9.5-mm) sieve. However, if 5 to 25 % of the material is retained on the 3/8-in. (9.5-mm) sieve, Method B can be used but oversize corrections will be required (See 1.4). In this case, the only advantages to using Method B rather than Method C are that a smaller amount of sample is needed and the smaller mold is easier to use.

1.3.2.6 Other UsageIf this gradation requirement cannot be met, then Method C may be used.

1.3.3 Method C:

1.3.3.1 Mold6-in. (152.4-mm) diameter.

1.3.3.2 MaterialPassing ¾-in. (19.0-mm) sieve.

1.3.3.3 LayersFive.

1.3.3.4 Blows per layer56.

1.3.3.5 UsageMay be used if 30 % or less (see 1.4) by mass of the material is retained on the ¾-in. (19.0-mm) sieve.

1.3.4 The 6-in. (152.4-mm) diameter mold shall not be used with Method A or B.

Note 2—Results have been found to vary slightly when a material is tested at the same compactive effort in different size molds, with the smaller mold size typically yielding larger values of unit weight and density (1).

1.4 If the test specimen contains more than 5 % by mass of oversize fraction (coarse fraction) and the material will not be included in the test, corrections must be made to the unit weight and molding water content of the test specimen or to the appropriate field in-place unit weight (or density) test specimen using Practice D4718.

1.5 This test method will generally produce a well-defined maximum dry unit weight for non-free draining soils. If this test method is used for free-draining soils the maximum unit weight may not be well defined, and can be less than obtained using Test Methods D4253.

1.6 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by these test methods.

1.6.1 For purposes of comparing measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal or significant digits in the specified limits.

1.6.2 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the users objectives; it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analytical methods for engineering design.

1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard, except for units of mass. The units for mass are given in SI units only, g or kg.

1.7.1 It is common practice in the engineering profession to concurrently use pounds to represent both a unit of mass (lbm) and a force (lbf). This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. These test methods have been written using the gravitational system of units when dealing with the inch-pound system. In this system, the pound (lbf) represents a unit of force (weight). However, the use of balances or scales recording pounds of mass (lbm) or the recording of density in lbm/ft3 shall not be regarded as a nonconformance with this standard.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.9 WarningMercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPAs website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercury containing products or both into your state may be prohibited by state law.

ASTM D 3080/D3080M : 2011 Standard Test Method for Direct Shear Test of Soils Under Consolidated Drained Conditions (Withdrawn 2020)
ASTM D 4718/D4718M : 2015 Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles
ASTM A 807/A807M : 2017 Standard Practice for Installing Corrugated Steel Structural Plate Pipe for Sewers and Other Applications
ASTM D 2937 : 2017 : EDT 2 Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method
ASTM D 5321/D5321M : 2019 Standard Test Method for Determining the Shear Strength of Soil-Geosynthetic and Geosynthetic-Geosynthetic Interfaces by Direct Shear
ASTM C 1479 : 2016 Standard Practice for Installation of Precast Concrete Sewer, Storm Drain, and Culvert Pipe Using Standard Installations
ASTM D 7243 : 2011 Standard Guide for Measuring the Saturated Hydraulic Conductivity of Paper Industry Sludges
ASTM D 5030/D5030M : 2013 : REV A Standard Test Methods for Density of Soil and Rock in Place by the Water Replacement Method in a Test Pit
ASTM D 5874 : 2016 Standard Test Methods for Determination of the Impact Value (IV) of a Soil
ASTM C 1170/C1170M : 2014 : EDT 1 Standard Test Method for Determining Consistency and Density of Roller-Compacted Concrete Using a Vibrating Table
ASTM D 7380 : 2015 Standard Test Method for Soil Compaction Determination at Shallow Depths Using 5-lb (2.3 kg) Dynamic Cone Penetrometer
ASTM C 1245/C1245M : 2012 Standard Test Method for Determining Relative Bond Strength Between Hardened Roller Compacted Concrete Lifts (Point Load Test) (Withdrawn 2019)
ASTM E 2277 : 2014 Standard Guide for Design and Construction of Coal Ash Structural Fills
ASTM B 789/B789M : 2016 Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
ASTM D 6938 : 2017 : REV A Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)
ASTM D 7830/D7830M : 2014 Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge
ASTM D 5080 : 2017 Standard Test Method for Rapid Determination of Percent Compaction
ASTM D 1452/D1452M : 2016 Standard Practice for Soil Exploration and Sampling by Auger Borings
ASTM D 5084 : 2016 : REV A Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter
ASTM E 2278 : 2013 Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage
ASTM D 4914/D4914M : 2016 Standard Test Methods for Density of Soil and Rock in Place by the Sand Replacement Method in a Test Pit
ASTM D 653 : 2014 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 2167 : 2015 Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method (Withdrawn 2024)
ASTM D 8167/D8167M : 2018 : REV A Standard Test Method for In-Place Bulk Density of Soil and Soil-Aggregate by a Low-Activity Nuclear Method (Shallow Depth)
ASTM D 6539 : 2013 Standard Test Method for Measurement of the Permeability of Unsaturated Porous Materials by Flowing Air (Withdrawn 2022)
ASTM D 6758 : 2018 Standard Test Method for Measuring Stiffness and Apparent Modulus of Soil and Soil-Aggregate In-Place by Electro-Mechanical Method
ASTM C 593 : 2006 : R2011 Standard Specification for Fly Ash and Other Pozzolans for Use With Lime for Soil Stabilization
ASTM D 8204 : 2018 Standard Practice for Burial and Retrieval of Samples in a Test Pad to Evaluate Installation Effects on Geosynthetic Clay Liners
ASTM D 7765 : 2018 : REV A Standard Practice for Use of Foundry Sand in Structural Fill and Embankments
ASTM D 4253 : 2016 Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
ASTM D 5856 : 2015 Standard Test Method for Measurement of Hydraulic Conductivity of Porous Material Using a Rigid-Wall, Compaction-Mold Permeameter (Withdrawn 2024)
ASTM D 6270 : 2017 Standard Practice for Use of Scrap Tires in Civil Engineering Applications
ASTM D 1556/D1556M : 2015 : EDT 1 Standard Test Method for Density and Unit Weight of Soil in Place by Sand-Cone Method (Withdrawn 2024)
ASTM D 6243/D6243M : 2016 Standard Test Method for Determining the Internal and Interface Shear Strength of Geosynthetic Clay Liner by the Direct Shear Method
ASTM D 7100 : 2011 Standard Test Method for Hydraulic Conductivity Compatibility Testing of Soils with Aqueous Solutions
ASTM E 1266 : 2012 Standard Practice for Processing Mixtures of Lime, Fly Ash, and Heavy Metal Wastes in Structural Fills and Other Construction Applications
ASTM C 1479M : 2016 Standard Practice for Installation of Precast Concrete Sewer, Storm Drain, and Culvert Pipe Using Standard Installations (Metric)
ASTM E 2243 : 2013 Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Re-contouring and Highwall Reclamation
ASTM D 7698 : 2011 : REV A Standard Test Method for In-Place Estimation of Density and Water Content of Soil and Aggregate by Correlation with Complex Impedance Method
ASTM D 1883 : 2016 Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils
ASTM D 6913/D6913M : 2017 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM F 1668 : 2016 Standard Guide for Construction Procedures for Buried Plastic Pipe
ASTM D 7762 : 2018 Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash

ASTM D 3740 : 2012-06 PRACTICE FOR MINIMUM REQUIREMENTS FOR AGENCIES ENGAGED IN TESTING AND/OR INSPECTION OF SOIL AND ROCK AS USED IN ENGINEERING DESIGN AND CONSTRUCTION
ASTM C 127 : 2015 : REDLINE Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate (Withdrawn 2024)
ASTM D 854 : 2014 : REDLINE Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer (Withdrawn 2023)
ASTM D 698 : 2013-05 TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3]))
IEEE/ASTM SI_10-2010 American National Standard for Metric Practice
ASTM D 5030 : 2004 Standard Test Method for Density of Soil and Rock in Place by the Water Replacement Method in a Test Pit
ASTM C 136 : 2006 Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
ASTM E 11 : 2017 : REDLINE Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
ASTM D 4753 : 2015 : REDLINE Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing
ASTM D 4253 : 2016 : REDLINE Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
ASTM C 670 : 2015 : REDLINE Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
ASTM D 6026 : 2013 : REDLINE Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 6913 : 2004 : EDT 2 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM D 653 : 2014 : REDLINE Standard Terminology Relating to Soil, Rock, and Contained Fluids

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.