ASTM D 1879 : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Exposure of Adhesive Specimens to Ionizing Radiation
Hardcopy , PDF
11-11-2014
English
01-03-2006
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 15.06, 2015 Defines conditions for the exposure of polymeric adhesives in bonded specimens to ionizing radiation prior to determination of radiation-induced changes in physical or chemical properties.
| Committee |
D 14
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2006
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 The purpose of this practice is to define conditions for the exposure of polymeric adhesives in bonded specimens to ionizing radiation prior to determination of radiation-induced changes in physical or chemical properties. This recommended practice specifically covers the following kinds of radiation: gamma or X-ray radiation, electron or beta radiation, neutrons, and mixtures of these such as reactor radiation.
1.2 This practice specifies only the conditions of irradiation but does not cover the preparation of test specimens, testing conditions, or the evaluation of test. These are covered in the various ASTM methods or specifications for specific materials.
1.3 This practice covers procedures for the following five types of exposure:
ProcedureA-Exposure at ambient conditions.
ProcedureB-Exposure at controlled temperature.
ProcedureC-Exposure in a medium other than air.
ProcedureD-Exposure under load.
ProcedureE-Exposure combining two or more of the variables listed in Procedures A to D. Note 1
The problems of measuring the properties of materials during irradiation involve shielding and remote control facilities and are, therefore, not considered in this practice.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5.1 Electrical Hazard:
1.5.2 Radio Frequency:
| ASTM D 6465 : 1999 : R2016 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ISO/ASTM 51702:2013 | Practice for dosimetry in a gamma facility for radiation processing |
| ASTM E 720 : 2016 : REDLINE | Standard Guide for Selection and Use of Neutron Sensors for Determining Neutron Spectra Employed in Radiation-Hardness Testing of Electronics |
| ISO/ASTM 51818:2013 | Practice for dosimetry in an electron beam facility for radiation processing at energies between 80 and 300 keV |
| ISO/ASTM 51261:2013 | Practice for calibration of routine dosimetry systems for radiation processing |
| ASTM E 170 : 2017 : REDLINE | Standard Terminology Relating to Radiation Measurements and Dosimetry |
| ANSI N1.1 : 1976 | NUCLEAR SAFETY - CRITICAL EXPERIMENTS, SAFETY GUIDE FOR THE PERFORMANCE OF |
| ASTM D 907 : 2015 : REDLINE | Standard Terminology of Adhesives |
| IEEE 323-2003 | IEEE Standard for Qualifying Class 1E Equipment for Nuclear Power Generating Stations |
| ASTM E 261 : 2016 : REDLINE | Standard Practice for Determining Neutron Fluence, Fluence Rate, and Spectra by Radioactivation Techniques |
| ASTM D 2953 : 1971 | Classification System for Polymeric Materials for Service in Ionizing Radiation (Withdrawn 1984) |
| ISO/ASTM 51649:2015 | Practice for dosimetry in an electron beam facility for radiation processing at energies between 300 keV and 25 MeV |
| ASTM E 666 : 2014 : REDLINE | Standard Practice for Calculating Absorbed Dose From Gamma or X Radiation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.