ASTM D 2103 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Polyethylene Film and Sheeting
29-11-2023
English
07-04-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.01, 2015 Defines the classification of polyethylene film and sheeting up to 0.3 mm (0.012 in.) in thickness, inclusive.
| Committee |
D 20
|
| DevelopmentNote |
Supersedes L P 512 (C). (05/2004)
|
| DocumentType |
Redline
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the classification of polyethylene film and sheeting up to 0.3 mm (0.012 in.) in thickness, inclusive. The film or sheeting may contain additives for the improvement of the surface properties, pigments, or stabilizers, or combinations thereof.
Note 1:Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 0.254 mm (0.010 in.).
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all the requirements as governed by the producer and end user are also met (see Note 2).
Note 2:Guide D7209 describes terminology and definitions related to recycled plastics.
Note 3:There is no known ISO equivalent to this standard.
| MIL-S-44384 Base Document:1989 | Suit, Contamination Avoidance, Liquid Protection (Scalp) (No S/S Document) |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 5748 : 1995 : R2001 | Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film |
| ASTM D 3020 : 1989 | Specification for Polyethylene and Ethylene Copolymer Plastic Sheeting for Pond, Canal and Reservoir Lining (Withdrawn 1996) |
| ASTM D 3981 : 2009 : REV A : R2016 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 5459 : 1995 | Standard Test Method for Machine Direction Elastic Recovery and Permanent Deformation and Stress Retention of Stretch Wrap Film |
| ASTM D 4649 : 2003 : R2016 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ASTM D 4801 : 2008 | Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm [0.010 in.] and Greater |
| ASTM D 5459 : 1995 : R2001 | Standard Test Method for Machine Direction Elastic Recovery and Permanent Deformation and Stress Retention of Stretch Wrap Film |
| ASTM D 4397 : 2016 : REDLINE | Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications |
| ACI 325.7R : 1988 | RECOMMENDATIONS FOR DESIGNING PRESTRESSED CONCRETE PAVEMENTS |
| ASTM D 5459 : 1995 : R2012 | Standard Test Method for Machine Direction Elastic Recovery and Permanent Deformation and Stress Retention of Stretch Wrap Film |
| SAE J2983_201212 | Recommended Practice for Determining Material Properties of Li-Battery Separator |
| ASTM D 5459 : 1995 : R2007 | Standard Test Method for Machine Direction Elastic Recovery and Permanent Deformation and Stress Retention of Stretch Wrap Film |
| ASTM D 5748 : 1995 : R2012 | Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film |
| ASTM D 5748 : 1995 | Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film |
| ASTM D 4649 : 2003 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ASTM D 3981 : 2009 : REV A | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ANSI Z86.11 : 1985 | LENSES FOR MASKS FOR RECREATIONAL SKIN AND SCUBA DIVING, |
| MIL S 0044384 : A | SUIT, CONTAMINATION AVOIDANCE, LIQUID PROTECTION (SCALP) |
| ASTM D 4801 : 2008 : R2016 | Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater |
| ASTM C 883 : 1989 | Standard Test Method for Effective Shrinkage of Epoxy-Resin Systems Used With Concrete (Withdrawn 1996) |
| ASTM D 4635 : 2016 : REDLINE | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ANSI Z80.1 : 2015 | OPHTHALMICS - PRESCRIPTION OPHTHALMIC LENSES - RECOMMENDATIONS |
| ASTM D 3981 : 2009 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 5748 : 1995 : R2007 | Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film |
| ASTM D 4649 : 2003 : R2009 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ASTM E 96/E96M : 2016 : REDLINE | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM D 1894 : 2014 : REDLINE | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 2839 : 2016 : REDLINE | Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene |
| ASTM D 7209 : 2006 | Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
| ASTM D 1004 : 2013 : REDLINE | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D 4321 : 2015 : REDLINE | Standard Test Method for Package Yield of Plastic Film (Withdrawn 2024) |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 2457 : 2013 : REDLINE | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 1003 : 2013 : REDLINE | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 1922 : 2015 : REDLINE | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 4703 : 2016 : REDLINE | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 6988 : 2013 : REDLINE | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 1746 : 2015 : REDLINE | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM F 1249 : 2013 : REDLINE | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 3892 : 2015 : REDLINE | PRACTICE FOR PACKAGING/PACKING OF PLASTICS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.