![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 3275 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials
Hardcopy , PDF
09-06-2023
English
14-11-2018
This classification system covers melt processible molding, extrusion, and coating materials of ethylene-chlorotrifluoroethylene (E-CTFE) fluoroplastics.
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
4
|
ProductNote |
THIS STANDARD ALSO REFERS TO IEEE/ASTM SI-10
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This classification system covers melt processible molding, extrusion, and coating materials of ethylene-chlorotrifluoroethylene (E-CTFE) fluoroplastics. The resin is a copolymer of ethylene and chlorotrifluoroethylene containing approximately 80 weight % of chlorotrifluoroethylene.
1.2The values stated in SI units, as detailed in IEEE/ASTM SI-10, are to be regarded as standard.
1.3The following precautionary statement pertains only to the test methods portion, Section 11 of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:Although this classification system and ISO 20568-1 and ISO 20568-2 differ in approach or detail, data obtained using either are technically equivalent.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 4000 : 2023 | Standard Classification System for Specifying Plastic Materials |
ASTM D 4967 : 2021 | Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing, and Strength Components in Fiber-Optic Cables |
ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
ASTM D 4967 : 1999 : R2013 | Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables |
ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 1708 : 1996 | Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens |
ASTM D 1238 : 2000 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2004 : REV C | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1708 : 2006 : REV A | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
ASTM D 150 : 2022 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
ASTM D 1238 : 2023 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 1238 : 2013 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2010 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 2863 : 2008 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 1708 : 2002 | Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 1708 : 2006 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2863 : 2012 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 2863 : 2000 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 4591 : 2001 | Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry |
ASTM D 2863 : 2006 : REV A | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 4591 : 2007 | Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry |
ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2863 : 2009 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 4591 : 2007 : R2012 | Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry |
ASTM D 4591 : 1997 | Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry |
ASTM D 4591 : 2017 | Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry |
ASTM D 2863 : 1995 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-like Combustion of Plastics (Oxygen Index) |
ASTM D 2863 : 2019 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
ASTM D 1238 : 2004 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 2863 : 2006 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 1708 : 2013 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
ASTM D 2863 : 2017 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 1708 : 2010 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 1238 : 2001 : EDT 1 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1708 : 2002 : REV A | Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens |
ASTM D 150 : 2018 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
ASTM D 2863 : 2017 : REV A | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 1238 : 2020 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2004 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1708 : 2018 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
ASTM D 2863 : 2010 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 2863 : 2012 : EDT 1 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 4591 : 2022 | Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry |
ASTM D 2863 : 2013 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.