ASTM D 3299 : 2018
Current
The latest, up-to-date edition.
Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks
Hardcopy , PDF
English
01-08-2018
This specification covers cylindrical tanks fabricated by filament winding for above-ground vertical installation, to contain aggressive chemicals at atmospheric pressure as classified herein, and made of a commercial-grade polyester or vinylester resin. Included are requirements for materials,properties, design, construction, dimensions, tolerances,workmanship, and appearance.1.2 This specification does not cover the design of vessels intended for pressure above atmospheric or under vacuum conditions, except as classified herein, or vessels intended for use with liquids heated above their flash points.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 Special design consideration shall be given to tanks subject to environmental and/or mechanical forces such as seismic, wind, ice, agitation, or fluid dynamic forces, to operational service temperatures greater than 180°F (82°C) and to tanks with unsupported bottoms.1.5 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1—There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations.Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
17
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification covers cylindrical tanks fabricated by filament winding for above-ground vertical installation, to contain aggressive chemicals at atmospheric pressure as classified herein, and made of a commercial-grade polyester or vinylester resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance.
1.2This specification does not cover the design of vessels intended for pressure above atmospheric or under vacuum conditions, except as classified herein, or vessels intended for use with liquids heated above their flash points.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 Special design consideration shall be given to tanks subject to environmental and/or mechanical forces such as seismic, wind, ice, agitation, or fluid dynamic forces, to operational service temperatures greater than 180°F (82°C) and to tanks with unsupported bottoms.
1.5The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 5421 : 2015 | Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 5364 : 2014 : R2019 | Standard Guide for Design, Fabrication, and Erection of Fiberglass Reinforced (FRP) Plastic Chimney Liners with Coal-Fired Units |
ASTM D 4024 : 2012 | Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
ASTM D 5421 : 2015 | Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM F 412 : 2024 | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 2583 : 2013 : REV A | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) |
ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
ASTM D 5421 : 1993 | Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 2584 : 2002 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
ASTM D 2584 : 2008 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 2584 : 1994 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 2583 : 2006 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM D 4024 : 2015 | Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 1599 : 2018 : R2024 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 2583 : 2013 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM D 2584 : 2011 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 2997 : 2001 | Standard Specification for Centrifugally Cast "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM C 582 : 1995 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 4024 : 2022 | Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 2996 : 2001 | Standard Specification for Filament-Wound "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 4024 : 2000 | Standard Specification for Machine Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 2996 : 2017 | Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 5421 : 2000 | Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 2584 : 1968 | Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 5421 : 2005 | Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM F 412 : 2023 | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 4024 : 2005 | Standard Specification for Machine Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 2996 : 2001 : R2007 : EDT 1 | Standard Specification for Filament-Wound "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 2996 : 2015 | Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 2583 : 2024 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM D 2584 : 2018 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
ASTM D 5421 : 2023 | Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 2996 : 1995 | Standard Specification for Filament-Wound "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 2997 : 2021 | Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 2996 : 2000 | Standard Specification for Filament-Wound "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM C 582 : 2023 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
ASTM D 2996 : 2023 | Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 2583 : 2007 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM D 2997 : 1999 | Standard Specification for Centrifugally Cast "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 2997 : 2001 : R2007 : EDT 1 | Standard Specification for Centrifugally Cast "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 2583 : 1995 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
ASTM C 582 : 2009 : R2016 | Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment |
ASTM D 5421 : 2005 : R2010 | Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges |
ASTM D 2997 : 2015 | Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.