ASTM D 378 : 2010 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Rubber (Elastomeric) Conveyor Belting, Flat Type
Hardcopy , PDF
14-06-2024
English
01-11-2016
CONTAINED IN VOL. 09.02, 2016 Defines the procedures for evaluating the physical properties of flat conveyor belting.
Committee |
D 11
|
DocumentType |
Test Method
|
Pages |
13
|
ProductNote |
Reconfirmed 2016
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1These test methods (and references) cover the procedures for evaluating the physical properties of flat conveyor belting. Performance criteria for belting will not be detailed here, but can be found through the RMA (Rubber Manufacturers Association) Conveyor and Elevator Belt Handbook, ANSI (American National Standards Institute), various governmental authorities, and the International Organization for Standardization (ISO). Belting for conveying and elevating materials generally is designated and defined as follows:
1.1.1Heavy Duty Conveyor—A heavy duty belt is defined as belting designed for bulk haulage of materials, such as stone, crushed rock, sand, metals ores, coal, wood chips, etc., and has a carcass strength (design) substantial enough to withstand conveyor system tensions of 160 PIW2 (pounds per inch of width) and above.
1.1.2Light Duty Conveyor—A light duty belt is defined as belting designed for conveying a variety of lower weight (density) materials, packages, industrial and electronic goods, and food products. These belts often are shorter in length and width, with less overall thickness than heavy duty belting, and are generally used in conveyor systems with tensions less than 160 PIW.
1.1.3General Description—Belting can have elastomeric coverings on one side, both sides, or neither side depending upon the specific application requirements. Belt coverings are comprised of various synthetic or natural rubber polymers, PVC, or other elastomeric materials, dependent upon application or customer requirements. The strength (load bearing) member(s) of most belting generally is a woven or interwoven carcass of synthetic or natural fibers, such as, but not limited to, polyester, nylon, polyaramide and cotton, as well as steel (cable/cord type or woven mesh).
1.2This standard does not purport to address all of the application specific testing available or safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 5963 : 1997 : REV A : R2001 | Standard Test Method for Rubber—Property Abrasion Resistance (Rotary Drum Abrader) |
ISO 505:2017 | Conveyor belts — Method for the determination of the tear propagation resistance of textile conveyor belts |
ASTM D 471 : 2016 : REV A | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM D 1894 : 2014 : REDLINE | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
ASTM D 1149 : 2016 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
ASTM D 1894 : 2011 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
ASTM D 5963 : 2004 | Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader) |
ASTM D 3183 : 2010 | Standard Practice for Rubber<span class='unicode'>—</span>Preparation of Pieces for Test Purposes from Products |
ISO 7590:2009 | Steel cord conveyor belts Methods for the determination of total thickness and cover thickness |
ASTM D 3767 : 2003 | Standard Practice for Rubber-Measurement of Dimensions |
ASTM D 4483 : 1999 | Standard Practice for Determining Precision for Test Method Standards in the Rubber and Carbon Black Industries |
ASTM D 1415 : 2005 | Standard Test Method for Rubber Property—International Hardness |
ASTM D 4483 : 2020 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ISO 282:1992 | Conveyor belts — Sampling |
ISO 7622-2:2015 | Steel cord conveyor belts Longitudinal traction test Part 2: Measurement of tensile strength |
ASTM D 4483 : 2005 : REV A | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ISO 8094:2013 | Steel cord conveyor belts — Adhesion strength test of the cover to the core layer |
ASTM D 1415 : 1988 : R1999 | Standard Test Method for Rubber Property-International Hardness |
ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
ASTM D 1894 : 2000 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
ASTM D 1415 : 2018 | Standard Test Method for Rubber Property—International Hardness |
ISO 4649:2017 | Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device |
ASTM D 1415 : 1988 : R2004 | Standard Test Method for Rubber Property—International Hardness |
ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 3183 : 2009 | Standard Practice for Rubber<span class='unicode'>—</span>Preparation of Pieces for Test Purposes from Products |
ASTM D 1894 : 2001 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
ASTM D 5963 : 2004 : R2015 | Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader) |
ASTM D 5963 : 2004 : R2019 | Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader) |
ASTM D 3183 : 201 | PRACTICE FOR RUBBER - PREPARATION OF PIECES FOR TEST PURPOSES FROM PRODUCTS |
ASTM D 1149 : 2015 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
ISO 9856:2016 | Conveyor belts Determination of elastic and permanent elongation and calculation of elastic modulus |
ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 3183 : 2010 : R2015 | Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products |
ASTM D 413 : 1998 | Standard Test Methods for Rubber Property-Adhesion to Flexible Substrate |
ASTM D 3767 : 2003 : R2014 | Standard Practice for Rubber—Measurement of Dimensions |
ARPM IP1 : 2011 | CONVEYOR AND ELEVATOR BELT HANDBOOK |
ASTM D 1149 : 2007 | Standard Test Methods for Rubber Deterioration-Cracking in an Ozone Controlled Environment |
ISO 7623:2015 | Steel cord conveyor belts — Cord-to-coating bond test — Initial test and after thermal treatment |
ASTM D 2240 : 2004 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
ISO 340:2013 | Conveyor belts Laboratory scale flammability characteristics Requirements and test method |
ISO 283:2015 | Textile conveyor belts — Full thickness tensile strength, elongation at break and elongation at the reference load — Test method |
ASTM D 471 : 2016 : REV A : R2021 | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM D 3183 : 2007 | Standard Practice for Rubber—Preparation of Product Pieces for Test Purposes from Products |
ASTM D 1894 : 2014 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) |
ASTM D 5963 : 2022 | Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader) |
ASTM D 1894 : 2011 : EDT 1 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 3767 : 2003 : R2008 | Standard Practice for Rubber<span class='unicode'>—</span>Measurement of Dimensions |
ISO 284:2012 | Conveyor belts — Electrical conductivity — Specification and test method |
ASTM D 5963 : 1997 : REV A | Standard Test Method for Rubber—Property Abrasion Resistance (Rotary Drum Abrader) |
ASTM D 1149 : 2018 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
ASTM D 1415 : 1968 | Standard Test Method for International Hardness Of Vulcanized Rubber |
ASTM D 2240 : 2015 : R2021 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1415 : 1988 : R1994 | Standard Test Method for Rubber Property-International Hardness |
ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 865 : 2011 | Standard Test Method for Rubber<char: emdash>Deterioration by Heating in Air (Test Tube Enclosure) |
ASTM D 3183 : 1984 : R1998 | Standard Practice for Rubber-Preparation of Pieces for Test Purposes from Products |
ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 1149 : 2007 : R2012 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
ASTM D 2240 : 2003 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 4483 : 2005 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
CFR 30(PTS1-199) : JUL 2017 | MINERAL RESOURCES - MINE SAFETY & HEALTH ADMINISTRATION, DEPARTMENT OF LABOUR |
ASTM D 1149 : 1978 : REV A | Standard Test Method for Rubber Deterioration - Surface Ozone Cracking In A Chamber ( Flat Specimen) |
ASTM D 2240 : 2002 : REV B | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 5963 : 2004 : R2010 : EDT 1 | Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader) |
ASTM D 1415 : 2006 : R2012 | Standard Test Method for Rubber Property—International Hardness |
ASTM D 3767 : 2003 : R2020 | Standard Practice for Rubber—Measurement of Dimensions |
ASTM D 5963 : 1997 : REV A : R2001 : EDT 1 | Standard Test Method for Rubber Property-Abrasion Resistance (Rotary Drum Abrader) |
ASTM D 3767 : 1996 | Standard Practice for Rubber-Measurement of Dimensions |
ASTM D 1415 : 2006 | Standard Test Method for Rubber Property—International Hardness |
ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 4483 : 2014 : REV A | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 4483 : 2014 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 5963 : 2004 : R2010 | Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader) |
ASTM D 1894 : 2008 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
ASTM D 2240 : 2005 | Standard Test Method for Rubber Property—Durometer Hardness |
ISO 7622-1:2013 | Steel cord conveyor belts — Longitudinal traction test — Part 1: Measurement of elongation |
ASTM D 4483 : 2018 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 4483 : 2005 : REV A : R2011 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
ASTM D 4483 : 2014-02 | PRACTICE FOR EVALUATING PRECISION FOR TEST METHOD STANDARDS IN THE RUBBER AND CARBON BLACK MANUFACTURING INDUSTRIES |
ASTM D 2240 : 2005 : R2010 | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
ASTM D 1894 : 2006 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
ASTM D 3183 : 2002 | Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products |
ASTM D 2240 : 2002 : REV A | Standard Test Method for Rubber Property—Durometer Hardness |
ASTM D 3183 : 2010 : R2019 | Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products |
ASTM D 3767 : 2001 | Standard Practice for Rubber-Measurement of Dimensions |
ASTM D 1149 : 1999 | Standard Test Method for Rubber Deterioration-Surface Ozone Cracking in a Chamber |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.