![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 445 : 2024
Current
The latest, up-to-date edition.
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
Hardcopy , PDF
English
01-04-2024
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
16
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This test method specifies a procedure for the determination of the kinematic viscosity, ν, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η, can be obtained by multiplying the kinematic viscosity, ν, by the density, ρ, of the liquid.
Note 1:For the measurement of the kinematic viscosity and viscosity of bitumens, see also Test Methods D2170 and D2171.
Note 2:ISO 3104 corresponds to Test Method D445 – 03.
1.2The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to liquids for which primarily the shear stress and shear rates are proportional (Newtonian flow behavior). If, however, the viscosity varies significantly with the rate of shear, different results may be obtained from viscometers of different capillary diameters. The procedure and precision values for residual fuel oils, which under some conditions exhibit non-Newtonian behavior, have been included.
1.3The range of kinematic viscosities covered by this test method is from 0.2 mm2/s to 300 000 mm2/s (see Table A1.1) at all temperatures (see 6.3 and 6.4). The precision has only been determined for those materials, kinematic viscosity ranges and temperatures as shown in the footnotes to the precision section.
1.4The values stated in SI units are to be regarded as standard. The SI unit used in this test method for kinematic viscosity is mm2/s, and the SI unit used in this test method for dynamic viscosity is mPa·s. For user reference, 1 mm2/s = 10-6 m2/s = 1 cSt and 1 mPa·s = 1 cP = 0.001 Pa·s.
1.5WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
NS-EN ISO 23581:2024 | Petroleum products and related products - Determination of kinematic viscosity - Method by Stabinger type viscometer (ISO 23581:2024) |
ASTM D 88/D88M : 2007 : R2024 | Standard Test Method for Saybolt Viscosity |
ASTM D 8291 : 2024 | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
ASTM D 2270 : 2024 | Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 °C and 100 °C |
ASTM D 7566 : 2024 : REV A | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
ASTM D 5621 : 2024 | Standard Test Method for Sonic Shear Stability of Hydraulic Fluids |
ASTM D 6469 : 2024 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
ASTM D 8279 : 2024 | Standard Test Method for Determination of Timing-Chain Wear in a Turbocharged, Direct-Injection, Spark-Ignition, Four-Cylinder Engine |
ASTM D 396 : 2024 | Standard Specification for Fuel Oils |
ASTM D 5704 : 2024 | Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles |
ASTM D 8565 : 2024 | Standard Specification for Glycol-Based Coolants for Fuel Cell Electric Vehicles |
ASTM D 2170/D2170M : 2024 | Standard Test Method for Kinematic Viscosity of Asphalts |
ASTM D 8256 : 2023 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 2162 : 2021 | Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 4682 : 2018 | Standard Specification for Miscibility with Gasoline and Fluidity of Two-Stroke-Cycle Gasoline Engine Lubricants |
ASTM D 6448 : 2016 : R2022 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
ASTM D 2532 : 2022 | Standard Test Method for Viscosity and Viscosity Change After Standing at Low Temperature of Aircraft Turbine Lubricants |
ASTM D 6514 : 2003 : R2019 : EDT 1 | Standard Test Method for High Temperature Universal Oxidation Test for Turbine Oils |
ASTM D 341 : 2020 : EDT 1 | Standard Practice for Viscosity-Temperature Equations and Charts for Liquid Petroleum or Hydrocarbon Products |
ASTM D 8111 : 2023 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
ASTM D 5900 : 2023 | Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM) |
ASTM D 7412 : 2022 | Standard Test Method for Condition Monitoring of Phosphate Antiwear Additives in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
ASTM D 4304 : 2022 | Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines |
ASTM D 6666 : 2020 | Standard Guide for Evaluation of Aqueous Polymer Quenchants |
ASTM D 7414 : 2022 | Standard Test Method for Condition Monitoring of Oxidation in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 6871 : 2017 | Standard Specification for Natural (Vegetable Oil) Ester Fluids Used in Electrical Apparatus |
ASTM D 4486 : 2023 | Standard Test Method for Kinematic Viscosity of Volatile and Reactive Liquids |
ASTM D 4052 : 2022 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM F 2084/F2084M : 2001 : R2024 | Standard Guide for Collecting Containment Boom Performance Data in Controlled Environments |
ASTM D 7223 : 2021 | Standard Specification for Aviation Certification Turbine Fuel |
ASTM D 7422 : 2023 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4732 : 2013 : R2020 | Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
ASTM D 2270 : 2010 : R2016 | Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 °C and 100 °C |
ASTM D 7887 : 2020 | Standard Guide for Selection of Substitute, Non-hazardous, Liquid Filling Substances for Packagings Subjected to the United Nations Performance Tests |
ASTM D 4731 : 2013 : R2020 | Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable |
ASTM D 2225 : 2020 | Standard Test Methods for Silicone Liquids Used for Electrical Insulation |
ASTM D 7945 : 2023 | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer |
ASTM D 2669 : 2016 | Standard Test Method for Apparent Viscosity of Petroleum Waxes Compounded with Additives (Hot Melts) |
ASTM D 6074 : 2015 : R2022 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
ASTM D 892 : 2023 | Standard Test Method for Foaming Characteristics of Lubricating Oils |
ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 5966 : 2022 | Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine |
ASTM F 2161 : 2021 | Standard Guide for Instrument and Precision Bearing Lubricants—Part 1 Oils |
ASTM D 4054 : 2023 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
ASTM D 4142 : 1989 : R2022 | Standard Guide for Testing Epoxy Resins |
ASTM D 5621 : 2020 | Standard Test Method for Sonic Shear Stability of Hydraulic Fluids |
ASTM D 446 : 2012 : R2017 | Standard Specifications and Operating Instructions for Glass Capillary Kinematic Viscometers |
ASTM D 7468 : 2022 | Standard Test Method for Cummins ISM Test |
ASTM D 7624 : 2022 | Standard Test Method for Condition Monitoring of Nitration in In-Service Petroleum and Hydrocarbon-Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 8181 : 2019 | Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils |
ASTM E 3282 : 2022 | Standard Guide for NAPL Mobility and Migration in Sediments – Evaluation Metrics |
ASTM D 6984 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine |
ASTM D 6080 : 2018 : REV A | Standard Practice for Defining the Viscosity Characteristics of Hydraulic Fluids |
ASTM D 7583 : 2016 : R2023 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 2161 : 2020 | Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity |
ASTM D 6823 : 2008 : R2021 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
ASTM D 3699 : 2019 | Standard Specification for Kerosine |
ASTM D 4636 : 2017 | Standard Test Method for Corrosiveness and Oxidation Stability of Hydraulic Oils, Aircraft Turbine Engine Lubricants, and Other Highly Refined Oils |
ASTM D 6710 : 2021 | Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil |
ASTM D 5222 : 2023 | Standard Specification for Less Flammable High Molecular Weight Hydrocarbon Mineral Electrical Insulating Liquids |
ASTM D 7666 : 2012 : R2019 | Standard Specification for Triglyceride Burner Fuel |
ASTM D 7483 : 2021 | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer |
ASTM D 8092 : 2022 | Standard Test Method for Field Determination of Kinematic Viscosity Using a Microchannel Viscometer |
ASTM D 4174 : 2023 | Standard Practice for Cleaning, Flushing, and Purification of Petroleum Fluid Hydraulic Systems |
ASTM D 2893 : 2019 | Standard Test Methods for Oxidation Characteristics of Extreme-Pressure Lubrication Oils |
ASTM D 5282 : 2005 : R2020 | Standard Test Methods for Compatibility of Construction Material with Silicone Fluid Used for Electrical Insulation |
ASTM D 6709 : 2024 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine) |
ASTM D 6278 : 2020 : REV A | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
ASTM D 6751 : 2023 : REV A | Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels |
ASTM D 4603 : 2018 | Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer |
ASTM D 7415 : 2022 | Standard Test Method for Condition Monitoring of Sulfate By-Products in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 8226 : 2021 : REV A : EDT 1 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIF Spark Ignition Engine<rangeref></rangeref > |
ASTM D 471 : 2016 : REV A : R2021 | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM D 8506 : 2023 | Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems |
ASTM F 3401 : 2019 | Standard Test Method for Wax Binder Removal from Equestrian Synthetic Track Surfaces |
ASTM D 4378 : 2024 | Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines |
ASTM D 7467 : 2023 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 2502 : 2014 : R2019 : EDT 1 | Standard Test Method for Estimation of Mean Relative Molecular Mass of Petroleum Oils from Viscosity Measurements |
ASTM D 4889 : 2021 | Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Crude or Modified Isocyanates |
ASTM D 7279 : 2020 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer |
ASTM D 8240 : 2022 : EDT 1 | Standard Specification for Less-Flammable Synthetic Ester Liquids Used in Electrical Apparatus |
ASTM D 2880 : 2023 | Standard Specification for Gas Turbine Fuel Oils |
ASTM D 3236 : 2015 : R2021 | Standard Test Method for Apparent Viscosity of Hot Melt Adhesives and Coating Materials |
ASTM D 6439 : 2023 | Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems |
ASTM D 7484 : 2023 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine |
ASTM D 4878 : 2023 | Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Polyols |
ASTM D 8180 : 2023 | Standard Specification for Rerefined Mineral Insulating Liquid Used in Electrical Apparatus |
ASTM D 8324 : 2021 | Standard Guide for Selection of Environmentally Acceptable Lubricants for the U.S. Environmental Protection Agency (EPA) Vessel General Permit |
ASTM D 8114 : 2023 : REV A | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition |
ASTM D 4652 : 2020 | Standard Specification for Silicone Liquid Used for Electrical Insulation |
ASTM D 7566 : 2023 : REV B | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
ASTM D 8048 : 2024 | Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine |
ASTM F 3208 : 2020 | Standard Guide for Selecting Test Soils for Validation of Cleaning Methods for Reusable Medical Devices |
ASTM D 4283 : 1998 : R2022 | Standard Test Method for Viscosity of Silicone Fluids |
ASTM D 8074 : 2023 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 5964 : 2016 : R2021 | Standard Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil |
ASTM D 4504 : 1994 : R2018 | Standard Specification for Molded Polyethylene Open-Head-Pails for Industrial Shipping of Nonhazardous Goods |
ASTM D 1243 : 2022 : EDT 1 | Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers |
ASTM D 8279 : 2023 : REV A | Standard Test Method for Determination of Timing-Chain Wear in a Turbocharged, Direct-Injection, Spark-Ignition, Four-Cylinder Engine |
ASTM D 5372 : 2020 | Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids |
ASTM D 333 : 2001 : R2021 | Standard Guide for Clear and Pigmented Lacquers |
ASTM D 7155 : 2020 | Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils |
ASTM D 8291 : 2023 : REV A | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
ASTM D 8278 : 2020 | Standard Specification for Digital Contact Thermometers for Test Methods Measuring Flow Properties of Fuels and Lubricants |
ASTM D 1795 : 2013 : R2021 | Standard Test Method for Intrinsic Viscosity of Cellulose |
ASTM D 2170/D2170M : 2022 | Standard Test Method for Kinematic Viscosity of Asphalts |
ASTM D 7596 : 2023 | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
ASTM D 7589 : 2016 : EDT 1 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref > |
ASTM D 3591 : 2022 | Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds |
ASTM D 6593 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 1763 : 2000 : R2021 | Standard Specification for Epoxy Resins |
ASTM D 6750 : 2023 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 8350 : 2024 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine |
ASTM D 7152 : 2023 | Standard Practice for Calculating Viscosity of a Blend of Petroleum Products |
ASTM D 8047 : 2023 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
ASTM D 1601 : 2018 | Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers |
ASTM D 5967 : 2021 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
ASTM D 1934 : 2020 | Standard Test Method for Oxidative Aging of Electrical Insulating Liquids by Open-Beaker Method |
ASTM D 4924 : 2021 | Standard Classification for Petroleum Waxes for Use in Rubber Compounding |
ASTM D 7665 : 2022 | Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids |
ASTM D 7156 : 2024 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
ASTM D 1655 : 2024 | Standard Specification for Aviation Turbine Fuels |
ASTM D 8147 : 2024 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
ASTM D 6891 : 2023 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVA Spark-Ignition Engine |
ASTM D 117 : 2022 | Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Liquids |
ASTM D 7528 : 2022 | Standard Test Method for Bench Oxidation of Engine Oils by ROBO Apparatus |
ASTM D 7549 : 2023 | Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure |
ASTM D 7863 : 2022 | Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids |
ASTM D 7826 : 2023 : REV B | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM D 6469 : 2020 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
ASTM D 5763 : 2022 : REV A | Standard Test Method for Oxidation and Thermal Stability Characteristics of Gear Oils Using Universal Glassware |
ASTM D 128 : 1998 : R2019 | Standard Test Methods for Analysis of Lubricating Grease |
ASTM D 7320 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 8323 : 2020 | Standard Guide for Management of In-Service Phosphate Ester-based Fluids for Steam Turbine Electro-Hydraulic Control (EHC) Systems |
ASTM D 4243 : 2023 | Standard Test Method for Measurement of Average Viscometric Degree of Polymerization of New and Aged Electrical Papers and Boards |
ASTM D 6923 : 2023 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure |
ASTM D 6158 : 2023 | Standard Specification for Mineral Hydraulic Oils |
ASTM E 2412 : 2023 : REV A | Standard Practice for Condition Monitoring of In-Service Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 6618 : 2023 | Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine |
ASTM F 631 : 2015 : R2020 | Standard Guide for Collecting Skimmer Performance Data in Controlled Environments |
ASTM D 2414 : 2023 : REV A | Standard Test Method for Carbon Black—Oil Absorption Number (OAN) |
ASTM D 3487 : 2016 : EDT 1 | Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus |
ASTM D 7416 : 2009 : R2020 | Standard Practice for Analysis of In-Service Lubricants Using a Particular Five-Part (Dielectric Permittivity, Time-Resolved Dielectric Permittivity with Switching Magnetic Fields, Laser Particle Counter, Microscopic Debris Analysis, and Orbital Viscometer) Integrated Tester |
ASTM D 2501 : 2014 : R2019 | Standard Test Method for Calculation of Viscosity-Gravity Constant (VGC) of Petroleum Oils |
ASTM D 7109 : 2022 : EDT 1 | Standard Test Method for Shear Stability of Polymer-Containing Fluids Using a European Diesel Injector Apparatus at 30 Cycles and 90 Cycles |
ASTM D 7720 : 2021 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
ASTM D 2226 : 1993 : R2022 | Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use |
ASTM D 7042 : 2021 : REV A | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
ASTM D 8164 : 2021 | Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing |
ASTM D 2603 : 2020 | Standard Test Method for Sonic Shear Stability of Polymer-Containing Oils |
ASTM F 715 : 2007 : R2023 | Standard Test Methods for Coated Fabrics Used for Oil Spill Control and Storage |
ASTM D 7417 : 2017 | Standard Test Method for Analysis of In-Service Lubricants Using Particular Four-Part Integrated Tester (Atomic Emission Spectroscopy, Infrared Spectroscopy, Viscosity, and Laser Particle Counter) |
ASTM D 5704 : 2022 : REV A | Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles |
ASTM D 8046 : 2021 | Standard Guide for Pumpability of Heat Transfer Fluids |
ASTM D 6681 : 2023 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure |
ASTM D 8185 : 2023 | Standard Guide for In-Service Lubricant Viscosity Measurement |
ASTM D 975 : 2023 : REV A | Standard Specification for Diesel Fuel |
ASTM D 8128 : 2022 | Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings |
ASTM D 5363 : 2016 | Standard Specification for Anaerobic Single-Component Adhesives (AN) |
ASTM D 2857 : 2022 | Standard Practice for Dilute Solution Viscosity of Polymers |
ASTM D 7578 : 2020 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
ASTM D 7973 : 2019 | Standard Guide for Monitoring Failure Mode Progression in Plain Bearings |
ASTM E 709 : 2021 | Standard Guide for Magnetic Particle Testing |
ASTM D 8029 : 2023 | Standard Specification for Biodegradable, Low Aquatic Toxicity Hydraulic Fluids |
ASTM D 4293 : 2022 | Standard Specification for Phosphate Ester-Based Fluids for Turbine Lubrication and Steam Turbine Electro-Hydraulic Control (EHC) Applications |
ASTM D 2140 : 2023 : EDT 1 | Standard Practice for Calculating Carbon-Type Composition of Insulating Oils of Petroleum Origin |
ASTM D 7752 : 2018 | Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids |
ASTM D 6224 : 2023 | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
ASTM D 4871 : 2011 : R2022 | Standard Guide for Universal Oxidation/Thermal Stability Test Apparatus |
ASTM D 7544 : 2023 | Standard Specification for Pyrolysis Liquid Biofuel |
ASTM D 5275 : 2020 | Standard Test Method for Fuel Injector Shear Stability Test (FISST) for Polymer Containing Fluids |
ASTM D 7844 : 2022 : REV A | Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 8274 : 2020 : REV A | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil by Portable Rapid Mid-Infrared Analyzer |
ASTM D 4040 : 2010 : R2019 | Standard Test Method for Rheological Properties of Paste Printing and Vehicles by the Falling-Rod Viscometer |
ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
ASTM D 396 : 2024 | Standard Specification for Fuel Oils |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.